Easy tips

What to do when your car heater is blowing cold air?

What to do when your car heater is blowing cold air? Start the engine with cap still open and let the engine idle for a few minutes. If the coolant level should drop as the thermostat opens, top it up as necessary. This should bleed off the air bubble. When the engine is fully warmed up, put the cap back on and take a drive to see if the heat output has returned. What causes a heater to blow cold air? The following are some issues that may be causing the heater to blow cold air: Low coolant levels. A...
Easy lifehacks

How much is a 454 LS6 worth?

How much is a 454 LS6 worth? Known as the “Pilot Car,” this particular 1970 Chevelle 454-ci Turbo-Jet LS6 is the earliest known and documented of 4,475 RPO LS6 models produced....Detailing.Vehicle:1970 Chevelle SS 454 LS6Number Produced:4,475Original List Price:$3,486SCM Valuation:$125,000–$150,000Tune Up Cost:$500 How much is a 1970 Chevelle SS 454 LS6 worth? Popular price guides put the values at $120,000 on the high end for a Chevelle hardtop and $166,000 for a convertible. Is the Chevy 454 long block engine on sale? Chevy 454 Long Block Crate Engine Sale. Our Chevy 454 Long Block Engine is on sale. This 7.4 liter...
Easy tips

How much does it cost to have an exhaust system installed?

How much does it cost to have an exhaust system installed? How much does car exhaust installation cost? $300 to $1,000, depending on the steel thickness and the quality. $100 to $300, depending on the materials and thickness. $25 to $100 per tip. How much does it cost to install a Flowmaster muffler? Just a muffler will probably run you about $70 for the install. Maybe more, maybe less depending on the shop. The throttle body spacer is a waste of money, as is the K&N intake. Itll sound cooler, but you will not see any noticeable performance gains, even...
Easy tips

How does a ground axle test work on an engine?

How does a ground axle test work on an engine? Electronic modules and many electrical components on the engine, transmission and passenger cabin use the chassis or firewall as an electrical common ground. This test checks for unwanted resistance at these points, including the secondary ground path between the battery and chassis, used by some older models. How to diagnose electrical ground issues onallcylinders? Starting at the battery, run the voltmeter probe from the battery to the first grounding point, usually a fender on muscle cars and trucks. Continue to where the fender attaches to the main body, and from...
Easy lifehacks

What causes a car to not shift into Park?

What causes a car to not shift into Park? Transmission Shift Cable Broke: If the cable connecting the shifter handle to the transmission is broken the car will not going into park, in fact the shifter will not work at all. Transmission cables usually break due to stretching, which happens over time or can result due to speed shifting or jamming the car into gear. What causes a Chevy transmission to not shift? Low transmission fluid level. Chevy transmission won't shift, stuck in 1st gear or limp mode - Speedometer may also display zero at all times. It could be...
Common questions

How do you find a trailer light short?

How do you find a trailer light short? Looks like Bassn is a faster typer! Well if brake and turn signal work then those wires ( green and yellow) seem ok and it would be the brown color common tail light wire that is bad. You can use a battery charger to check lights. Apply power to each individual lug on the connector and see what happens. How does a trailer light hook up to a vehicle? This vehicle-to-trailer wiring harness creates a standard trailer wiring connection by plugging into vehicle harness and tail light assembly, and then routing the...
Most popular

How do you turn off the change oil light?

How do you turn off the change oil light? Watch for the change oil light to flash. If it does not flash and remains on, turn the ignition key to the off position and then retry the procedure. After the change oil light flashes, it should go out. If the change oil remains on for five seconds (depending on the year and model Chevy), it may not have reset. How do you reset oil change indicator? Hold the button down until the "Oil" icon or word starts to flash, or the indicator lights show some other sign of resetting. Some...
Common questions

How can I tell how far an avalanche can go?

How can I tell how far an avalanche can go? Simple, just sight with an inclinometer (or trained eyeballs) to the top of the estimated starting zone, and estimate where the sight line intersects behind you (or lie down on the snow and sight). That’s all you need to get an idea of where you are in relation to the path runout. Why are avalanches dangerous in backcountry skiing? This is written from one backcountry skiing layman to another, with the simple purpose of conveying a concept I’ve found useful and practical over the years for increasing avalanche safety. Any...
Other

Why does my air conditioner not defrost?

Why does my air conditioner not defrost? The air blows best out the front vents and not so well on the feet. I switch the mode to defrost and you hear it shifting over, but never gets there and then blows hard out the front vents. I don't hear clicking like many people hear when the mode actuator is bad. What to do if your defroster wont blow out top vents? If you need further assistance with defroster not working on top vents, then seek out a professional, such as one from Your Mechanic, to help you. The statements expressed...
Other

How do you remove a master cylinder from a brake booster?

How do you remove a master cylinder from a brake booster? Step 2: Remove the master cylinder from the brake booster. Remove the master cylinder fasteners using a ratchet or wrench. Then pull the master cylinder away from the booster. Typically, the brake lines are long enough that this can be done without disconnecting the lines. Step 3: Disconnect the booster vacuum supply line. How does check valve on master cylinder work? The check valve is responsible for controlling the pressure inside the master cylinder. If this valve starts creating a problem then, it turns the soft and smooth pedal...