Easy tips

Where is the glow plug controller on a Chevy K20?

Where is the glow plug controller on a Chevy K20? Locate the glow plug controller under the dash, its a black box with about leave the blue wire intact and just take it off the terminal on the glow plug relay (so you Chevy K20 4X4 L Suburban w/R4 (CUCV clone project . wire for the card and the TM wiring diagram for its position is WRONG. Is the glow plug relay on the negative side? Beginning in , the L diesel utilized a combination glow plug relay and You can therefore test each individual glow plug wire or the...
Other

Where is the EVAP vent control valve located?

Where is the EVAP vent control valve located? (Tech Tip- The EVAP vent control valve is usually located under the car in the rear of the vehicle by or attached to the charcoal canister.) Verify with no power or ground supplied that you can blow through the valve’s openings. (If you can’t blow through the openings, the valve is stuck closed and needs to be replaced.) What is the trouble code on my Chevy Silverado? P0446 Chevy Silverado. March 6, 2019August 7, 2018. One of the most common trouble codes with the Chevy Silverado is the P0446 code. This trouble...
Common questions

How does auto stop start on Chevy Silverado work?

How does auto stop start on Chevy Silverado work? The system then automatically starts the engine back up as soon as it detects that the driver has lifted their foot off the brake pedal. Engine auto stop-start feature has occasionally been criticized by owners of vehicles with the feature. How do I reset Transmission Control Module Chevy Silverado? I have a 2001 Silverado. To reset my TCM I turn on the key to the on position press the gas pedal to the floor for 10 seconds and then turn the key off then release the gas pedal and wait about...
Other

What to do if your transmission shaft is leaking?

What to do if your transmission shaft is leaking? If your input shaft seal is leaking, then you will see transmission fluid dripping from the front of your bellhousing. IReplacing the seal will require removing your transmission which can be an expensive job. If that doesn’t make sense for your or your vehicle, use BlueDevil Transmission Sealer to restore that seal and stop the leak. How much does it cost to fix a transmission leak? Not to mention, a leak can cost you between 100 and 200 dollars if you take your car to a shop (If you have to...
Easy lifehacks

Are there any problems with my 2007 Chevy Impala?

Are there any problems with my 2007 Chevy Impala? 8/10 stars for my Chevy impala! My 2007 Chevy impala runs really well. The only issues that I have had are related to lack of care by the previous owner, but, otherwise it is in great shape! However, my tire sensor refuses to work, despite having been replaced multiple times. What's the speed of a 2007 Chevy Impala? "My 2007 Chevy Impala has developed a brand new problem today. Driving down the block to the store, the speedometer started fluctuating wildly. I was going a consistent speed of about 10 mph...
Common questions

Can a bad ECM cause a car to stall?

Can a bad ECM cause a car to stall? Engine Stalling or Misfiring Erratic engine behavior may also indicate a bad or failing ECM. A faulty computer may cause the vehicle to intermittently stall or misfire. The symptoms might come and go and not appear to have any sort of pattern to their frequency or severity. 3. Engine Performance Issues What are the symptoms of a bad ECM power relay? A bad relay may cause the vehicle to crank, but not start, or sometimes not even crank at all. 3. Battery drain or dead battery. A failed ECM power relay...
Common questions

How wide is a K5 Blazer?

How wide is a K5 Blazer? 1973–1991Second generationWheelbase106.5 in (2,705 mm)Length184.8 in (4,694 mm)Width79.6 in (2,022 mm)Height77.8 in (1,976 mm) Is there a 1987 Chevy K5 Blazer for sale? This 1987 Chevrolet K5 Blazer hits a true sweet spot. You get the unbeatable classic appearance of the 4x4 SUV with a removable hardtop. And because this is the later part of the series, you also g... More Info › Now for sale in Gateway Classic Cars Houston Showroom is this beefy silver 1987 Chevrolet K5 Blazer. When did the Chevy K5 Blazer get discontinued? The K5 Blazer was the smallest...
Most popular

How can I tell if my Chevy Equinox has a problem?

How can I tell if my Chevy Equinox has a problem? The car’s computer will then think that something is wrong and bring up a Check Engine light. Other common signs that will indicate there is a problem with the timing chain in your Chevrolet Equinox is if you get an Engine Position Performance code or a Camshaft Position Performance code. How does the Chevy Equinox stability system work? StabiliTrak is a GM specific vehicle stability system. It works by using a complex system of sensors to detect whether or not the vehicle is properly responding to your input in...
Most popular

Did they make a 63 El Camino?

Did they make a 63 El Camino? Depending on how well you know the GM product line, back in the '60s, Chevrolet stopped producing El Caminos from 1961-63. El Caminos started again in 1964. This '62 Chevy originally was a two-door Biscayne sedan. What was Ford's version of the El Camino? Ranchero The original Ranchero sold well enough to spawn a competitor from General Motors in 1959, the Chevrolet El Camino. When did Chevrolet stop making the El Camino? Production resumed for the 1964–1977 model years based on the Chevelle platform, and continued for the 1978–1987 model years based on...
Easy lifehacks

How is a center support bearing attached to a rear wheel drive car?

How is a center support bearing attached to a rear wheel drive car? On some rear wheel drive vehicles, the bearing block bolts thread into nuts that are solidly mounted or welded onto the frame. On some vehicles, two part nuts and bolts are used to attach the rear of the front driveshaft to the center support bearing. How do you replace a hub bearing on a Chevy Cobalt? Once you have the bearing most of the way in, take the 30mm socket and place it directly in the center of the new bearing and using a hammer carefully tap...