Easy lifehacks

Do you need a tank for on board Air?

Do you need a tank for on board Air? ARB CKMA12 On-Board High Performance Compressor Weight: 7.7 pounds. Output PSI: 100 psi maximum. Install Time: 15 minutes to 2 hours. Air Tool Usage: You would need to add either an auxiliary tank or use the twin compressor system. Can VIAIR compressor be mounted outside? Compressor can be mounted outside the vehicle if you have room for it (we suggest relocating the filter if do). Choose angle of compressor mount: right side up, sideways, or upside down (although VIAIR recommends mounting upright to keep longevity of the compressor and to avoid...
Other

How can I tell if my reverse light switch is not working?

How can I tell if my reverse light switch is not working? One way to test that the reverse light switch is not working is to remove it and then connect the wires that lead into and out of the switch to each other. Then, if you turn the car’s electrical systems on, the reverse lights should be on. This demonstrates that the lamp switch is the culprit and not any other part of the system. Where can I buy a reverse light switch? Call our customer service toll free at 888-844-3393 if you have any questions about our aftermarket...
Easy tips

What is a trim dash?

What is a trim dash? A dash trim is made up of 3 layers. These are the 3M adhesive backing and trim material. A dash trim is made up of 3 layers. These are the 3M adhesive backing and trim material. Do dash kits look good? Dash kits can look great, but doing too much can make the interior look cheap. Don't over do the amount of area covered. Also, ask for a sample of the material. What does a dash kit do? A dash kit is an automotive accessory which is meant to accentuate the dashboard and other interior...
Common questions

What to do when your gas tank keeps shutting off?

What to do when your gas tank keeps shutting off? Then if you can, when the gas tank is on vapors, carefully remove the gas tank filler neck and see if the anti splash back door is somewhat jamb shut at the base of the gas tank filler tube. Update: Began pulling lines off the evap/charcoal canister yesterday. The first tube I pulled off, charcoal pellets fell out on to the ground. Why does my gas pump keep cutting off? What this all means is that if you’re filling your tank and the pump keeps cutting off, something is blocking...
Other

How much horsepower did the Mustang SVO have?

How much horsepower did the Mustang SVO have? Turbocharged powerMustang SVO horsepower and torque ratings by yearYearPowerTorque1985175 hp (130 kW) @ 4400 rpm210 lb⋅ft (285 N⋅m) @ 3000 rpm1985.5205 hp (153 kW) @ 5000 rpm248 lb⋅ft (336 N⋅m) @ 3200 rpm1986200 hp (149 kW) @ 5000 rpm240 lb⋅ft (325 N⋅m) @ 3200 rpm When did the Ford Mustang SVO Turbo come out? The team’s first production car debuted in 1984. The Mustang SVO was only available with a 2.3 Liter turbocharged 4-cylinder engine and Borg-Warner T-5 5-speed manual transmission sourced from the all-new Ford Thunderbird Turbo Coupe to help reduce...
Easy tips

When was the R-134a refrigerant added to the market?

When was the R-134a refrigerant added to the market? As a replacement product R-134a was introduced into the automotive market in 1993. Like it’s predecessor, R-12, R-134a was and is used across a wide array of applications in the automotive world. You can find R-134a in your Ford Focus or you could find it in your gigantic Semi-Trucks or in your Gray-hound Bus. What kind of oil is used in R-134a air conditioner? PAG oil, or Polyalkylene Glycol, is a fully synthetic hygroscopic oil specifically designed for automotive air conditioner compressors. It is used in R-134a air conditioning systems to...
Easy tips

What causes low compression in a cylinder head?

What causes low compression in a cylinder head? Reasons for Low Compression in One Cylinder. 4. Bad Intake or Exhaust Valve: Intake and exhaust valves are present in every combustion chamber in the engine's cylinder head. The valves seal against a valve seat which is pressed into the cylinder head. Each of these pieces is made of a hardened metal that are finally ground to create the seal. Can a blown head gasket cause low compression? If two cylinders next to each other both have low pressure, a blown head gasket is a likely culprit. If you discover you do...
Easy lifehacks

Is there a 5.0 Coyote engine swap kit?

Is there a 5.0 Coyote engine swap kit? Planning a 5.0 Coyote swap? The PBH Coyote engine swap bracket kits let you use the accessories from any 1996-2010 GT/Cobra V8 – all brackets, hardware, tensioners, and belts are included. Looking to run a 6R80 6-speed automatic behind your Coyote or GT500 swapped project? Where can I get an engine swap kit? At Summit Racing Equipment, your engine swap just got a whole lot easier with these all-in-one engine swap kits. What kind of swap Kit do I need for a 1988 GM Truck? These LS swap kits are for 1988-1998...
Most popular

What should I do if I have an oil leak in my Ford?

What should I do if I have an oil leak in my Ford? If it indeed is leaking, Ford has a new-design cam plug (Part No. F1DZ-6266-A) that should take care of the situation once and for all. When installing the plug, make sure you drive it in straight and that there's plenty of anaerobic sealant on its outer circumference to avoid subsequent leaks. Is the Ford 3.0 engine a leaker? Any thoughts you might be able to share will be greatly appreciated. The 3.0's reputation as a "leaker" is fairly well established in industry circles, Jack. But it's vitally...
Easy lifehacks

What to do if compression reading is low on 5.0L engine?

What to do if compression reading is low on 5.0L engine? If you've gotten a very low compression reading from any one cylinder on your 5.0L engine (4.9L engine or 5.8L engine), the next step is to add a little bit of engine oil (to that cylinder) and re-check its compression to see if the compression pressure will go up or not. Why do I have no compression in my engine? If you are getting no compression at all in your cylinders, you probably have a bad timing belt or a broken camshaft. Now that you know some of the...