Most popular

Are there any aftermarket bare engine blocks available?

Are there any aftermarket bare engine blocks available? Whether you’re building a new engine or recovering from an under-the-hood incident you’d rather soon forget, explore our large selection of aftermarket bare engine blocks to complete your new power plant project. What kind of engine blocks do I Need? We have V6, V8, and L4 engine block types, and bare blocks of various materials including aluminum, billet aluminum, steel, cast iron, and ductile iron. Find the perfect foundation for your Chevy, Ford, or Mopar build-up, including Chevy 350 and 454, Ford 302 and 351w, Hemi, Corvette, LS, and LSX engines. How...
Common questions

How often do you really need to change the oil in your car?

How often do you really need to change the oil in your car? The Truth about Oil Changes Quick-lube chains say 3,000 miles, auto manufacturers recommend 5,000 to 7,500 miles and synthetic oil companies, 10,000. How often do you really need to change the oil in your car? Dear EarthTalk: How often do I really need to change my car’s oil? What's the average mileage for an oil change? Three Months, 3,000 Miles Or Longer?: The Truth about Oil Changes. Quick-lube chains say 3,000 miles, auto manufacturers recommend 5,000 to 7,500 miles and synthetic oil companies, 10,000. How often should...
Easy tips

What is the security starter relay controlled starter wiring diagram?

What is the security starter relay controlled starter wiring diagram? The security starter relay controlled car starter wiring diagram is as shown in the following picture. How does the starter connect to the battery? Usually, the ignition switch connects with a key or a button, and inside of it has the regular wire connects to the car battery. When the ignition switch is turned or pressed the button to start position, there will be a small current flow through the starter solenoid coil, allow sufficient current flow to the starter. What are the two circuits of a starter? Basic Wiring...
Most popular

How do you remove an EVAP vent solenoid?

How do you remove an EVAP vent solenoid? Step 9: Remove the old EVAP vent solenoid. After you've released the clips and unbolted the unit, it should come off the vehicle rather simply. In some cases, there is a secondary ground wire attached to the unit. If this is the case, simply remove the ground wire and the unit will come off. How does the EVAP purge solenoid work in a car? Hydrocarbon is distributed by the EVAP purge solenoid into the fuel system and burnt during the combustion process. The filtered hydrocarbons are converted to carbon dioxide and released...
Common questions

How much is a upper intake gasket?

How much is a upper intake gasket? Intake Manifold Gasket Replacement Cost The replacement cost of an intake manifold gasket is anywhere from $190 to $540. The cost of the labor will be anywhere from $170 to $420. The gasket itself is very inexpensive and will cost somewhere in the neighborhood of $20 to $120. How much is a lower intake gasket? Intake Manifold Gasket Replacement Cost - RepairPal Estimate. The average cost for intake manifold gasket replacement is between $281 and $337. Labor costs are estimated between $215 and $271 while parts are priced at $66. Where does the...
Other

Do you need to put new armrests in your car?

Do you need to put new armrests in your car? There’s no need to put new holes in the interior of your vehicle for a replacement armrest. Replace your damaged or worn out door armrests, seat armrests, or center console armrests with Genuine GM parts online through GMPartsNow for a perfect fit in your Chevrolet, Pontiac, Buick, Cadillac, GMC, or Saturn using existing screw holes. Can you change the armrests on the center console? Depending on your GM vehicle, door armrests in some models can be replaced separate from the inside door panel saving you time and hassle. Upgrade your...
Most popular

Can you run an engine on a engine cradle?

Can you run an engine on a engine cradle? You'll be fine. I ran my 455 Olds (2 of 'em) on the engine stand. First one was about 35 minutes, second one 2 1/2 hours. As long as there's a flexplate (not a flywheel) and no torque converter on the back, there's little torque reaction unless you open the throttle suddenly. Is it safe to drive with engine cradle damaged? If there is damage to the cradle, or damage to the car, such that the vehicle is actually shaking the car is not safe to use. In addition, driving the...
Easy tips

What are traction control and traction control lights on?

What are traction control and traction control lights on? Engine Management and traction control/stability lights on. Over the past week I noticed my J to be spluttering slightly in first and second gear, almost like a fuel pick up problem but tonight it got really bad.. Why does my traction control light keep blinking? They changed it and mentioned that now catalyst (not sure of english word, in exhaust system) could be a problem. And 2 days later, when going into a hill fully loaded traction control came on, stabilizer light came on and engine light was blinking when stepped...
Common questions

Does check engine light come on for low tire pressure?

Does check engine light come on for low tire pressure? There are many, many reasons that the check engine light may come on in you car, truck or SUV. A malfunctioning sensor, low tire pressure, low transmission fluid and so much more will cause the light to come on. How to fix a low tire pressure light? Next step in the process is to press the located button for three seconds. Once the light blinks for three times on the dashboard, this means the TPMS is reset. After this, turn off the engine and again start it after five seconds...
Most popular

Is finding top dead center?

Is finding top dead center? Find the center point between the two marks. That center point is top dead center. Be sure to remove the piston stop tool and return the spark plug prior to starting the engine. Reconnect the battery to restore power to the vehicle once you're done. What is a bottom dead center? Bottom dead center is the point at which the piston of an engine is nearest to the axis of the crankshaft. On a vertical engine, this is the lowest point that the piston reaches. During the compression stroke, the piston moves up from bottom...