Common questions

What are the different types of fuels?

What are the different types of fuels? ChemicalPrimary (natural)Secondary (artificial)Solid fuelswood, coal, peat, dung, etc.coke, charcoalLiquid fuelspetroleumdiesel, gasoline, kerosene, LPG, coal tar, naphtha, ethanolGaseous fuelsnatural gashydrogen, propane, methane, coal gas, water gas, blast furnace gas, coke oven gas, CNG What are the three types of fossil fuels? The three main forms of fossil fuels are coal, oil and natural gas. These three are also known by different names, such as petroleum for oil, and each type of fossil fuels exists in a different chemical state. Coal has been used for centuries for heat and to power steam engines. It is...
Most popular

What compound comes from burning fossil fuels?

What compound comes from burning fossil fuels? When fossil fuels are burned, they release nitrogen oxides into the atmosphere, which contribute to the formation of smog and acid rain. The most common nitrogen-related compounds emitted into the air by human activities are collectively referred to as nitrogen oxides. Is burning fossil fuels combustion? Fossil fuels, such as coal, oil and natural gas, are created when organic matter decays and becomes compressed beneath layer upon layer of sand, earth, rock and ocean. Burning fossil fuels yields carbon dioxide, water and energy; the process of burning fossil fuels is known as “combustion”....
Easy tips

Do you need a valley pan?

Do you need a valley pan? On the newer design engines the intake manifold incorporates the valley pan, the part that seals the top of the block and heads. If the tunnel ram intake does not have the casting that seals the block and heads to keep oil in and debris out, then yes you need one. What is a valley pan? A Valley pan or valley gasket is traditionally used to seal the lower intake manifold to the cylinder heads and engine. This gasket was vital because many of those engines have their coolant crossover built into the lower...
Easy tips

How do you reset the code on a 2014 Ford Edge?

How do you reset the code on a 2014 Ford Edge? To reprogRam the keyless entry pad on a Ford Edge, type in the factory code found in the owner's manual. Within 5 seconds, press the 1-2 button, and enter 5 digits that are personal and simple to remember. New numbers must be pressed within 5 seconds of one another to be stored by the Edge. Where to find factory code on Ford Edge? You will need to remove the trim panel, slide the release lever to the right then pull the trim panel out. For the latest model of...
Easy lifehacks

Is Ford listed in NSE?

Is Ford listed in NSE? Ford India Ltd. is not listed on NSE (View BSE) Should I sell my Ford stock? Ford Motor(F-N) Rating Stockchase rating for Ford Motor is calculated according to the stock experts' signals. A high score means experts mostly recommend to buy the stock while a low score means experts mostly recommend to sell the stock. Is Forward Industries stock a buy? Is Forward Industries stock A Buy? The Forward Industries stock holds several negative signals and despite the positive trend, we believe Forward Industries will perform weakly in the next couple of days or weeks....
Easy tips

What does it mean when the clutch pedal is hard?

What does it mean when the clutch pedal is hard? Hard clutch: A hard clutch could be caused due to a worn out pressure plate, air in the hydraulic line (in case of hydraulically operated clutches), or due to a clutch cable that needs lubrication. If you notice clutch judder, it is an indication that the clutch assembly including the flywheel might need replacement. What causes a clutch to feel too hard? Clutch master cylinder or slave cylinder is bad: Similar to a clutch that is too soft, a bad master cylinder or slave cylinder can cause your clutch to...
Easy tips

What does it mean when your gear shift is locked?

What does it mean when your gear shift is locked? What Does a Shift Lock Do for Automatic Transmissions? The shift lock release feature allows the driver to switch the available automatic transmission options. The shift lock button is usually a button found on top or side of the gear selector lever. With it, the driver can lock the gear to the desired option. How to release an automatic shift stuck in Park-car? Then, take off the foot and move the shift into park. In this way, the car will not roll and the parking brake will hold its weight,...
Most popular

What kind of timing pin does a 2.0L DOHC engine use?

What kind of timing pin does a 2.0L DOHC engine use? The flat bar and short timing pin are used on 2004-2012 2. 5L DOHC, 2. 3L DOHC 4V and 2. 0L DOHC engines that are found in Ford, Mercury and Mazda vehicles The flat bar and long timing pin are used on 2. 0L DOHC Zetec engines found in 1994-2003 Ford and Mercury vehicles Is it OK to replace timing chain on Ford engine? Chains are longer lived than most timing belts, and there are no recommended chain replacement intervals published by Ford for these engines. Even so, timing...
Easy tips

How does a GM anti theft system work?

How does a GM anti theft system work? Each GM anti-theft system disables different components. Some disable the engine starter, while others enable the starter but disable fuel injectors. None of them disable spark. So, first understand the difference between vehicle theft deterrent systems. GM used two strategies to determine if someone was trying to steal the vehicle. What to look for in an anti theft system? A tell-tale sign that you’ve got an anti-theft problem is a flashing “Theft” light. Here’s a brief primer on each system and what to look for. What happens if your anti theft system...
Most popular

How big is a Sears escape caliper wrench?

How big is a Sears escape caliper wrench? Sears and Napa have up to 3/8's "Caliper bits" try the 9mm. Bigger then a 10mm. Which is the bigest size they sell. A 12mm is way too big. Went thru all the mm and SAE sizes. What's the correct way to remove a brake caliper? Let the bolt soak for at least five minutes before attempting to remove. Make sure to remove it in the correct direction. Note: While we’re all taught that lefty-loosey – righty-tighty is the preferred method, some brake caliper bolts are reverse thread. This is where referring...