Easy lifehacks

What are the 4 wires on a PC fan?

What are the 4 wires on a PC fan? However, the 4-wire fan is a little different as it has the fourth 'control' wire to input a signal to the fan that commands it to speed up or speed down....4-wire fans explained.PINWIRE COLORFUNCTION1BlackGND (0V)2Yellow+12V3GreenSense/Tach4BlueControl/PWM Can you use a 4 pin fan on a 2 pin connector? Yes, the fan will work, but the speed of the fan won't be controlled by the motherboard because the voltage can't be controlled via just the two pins. Can you put a 4-pin fan into a 3 pin? FAQ: Can I run 4-pin PWM...
Most popular

Can you swap parts on a generation 3 LS engine?

Can you swap parts on a generation 3 LS engine? Even though most parts can interchange on LS Based engines, it is important to know the differences between a Generation 3 and Generation 4 LS engine. There are many things that are different between these two generations of engines and can really be difficult to decipher what parts you need for your build. When did the 6.0L Vortec engine come out? The 6.0L Vortec engine was first introduced in 1999, and some version of that engine is still present today. This engine is well known for having plenty of power...
Common questions

What was the problem with my GMC Sierra?

What was the problem with my GMC Sierra? Injector for Cyl 8 replaced. Engine light had come on three times in 2 weeks but issue not resolved until third time in to check it and at that time a Head Office GM specialist of some kind happened to be there and determined the issue was an injector. Truck ran fine before the work. What causes vibration in a GMC Sierra 1500? Vibration when in V4 mode some clamps were replaced on the exhaust system, the vibration is still there between 1200-1400 rpm. engine vibration in V4 mode, exhaust system replaced,...
Easy lifehacks

Where is the crankshaft sensor located?

Where is the crankshaft sensor located? Crankshaft sensors are located in the crank pulley, flywheel, camshaft or directly on the crankshaft. Crankshaft position sensors, which ensure that the vehicle starts and remains running, are one of the most important components of an engine. What is a bad crank sensor? A bad crank position sensor can worsen the way the engine idles, or the acceleration behaviour. If the engine is revved up with a bad or faulty sensor, it may cause misfiring, motor vibration or backfires. Acceleration might be hesitant, and abnormal shaking during engine idle might occur. How do you...
Most popular

What should I do after replacing my oil pan?

What should I do after replacing my oil pan? In order to ensure a good seal on your new oil pan, you will want to clean the mounting surface after you remove the old oil pan and gasket. You should use a gasket scraper or similar tool to remove any old gasket material without damaging the engine block or other mounting surfaces. How do you remove gasket from oil pan? Removing it should have been simple: use the plastic scraper to remove all of it, leaving bare metal, and many some gasket remover solution to remove any residue. Using a...
Easy tips

How to install a new throttle position sensor?

How to install a new throttle position sensor? Install your new sensor by working backward through the removal steps. Start by installing the sensor using the mounting screws. Next, connect your sensor to your vehicle's electrical system using a convenient electrical connector. You should be able to easily push it together and hear a distinct click. Check to ensure a firm connection. When is a bad throttle position sensor a warning sign? Engine won’t idle smoothly, idles too slowly, or stalls If you start to experience engine misfires, stalling, or rough idling when the car is stopped, it can also...
Easy lifehacks

What does the p0302 code on a cylinder 2 mean?

What does the p0302 code on a cylinder 2 mean? The P0302 code means that the cylinder 2 is misfiring or is randomly misfiring. Start by checking for intake leaks and if no leaks are found the next step is to replace the spark plugs on cylinder 2. What to do if the p0302 trouble code is still unresolved? If the P0302 trouble code is still unresolved, a problem with the powertrain control module is possible (this is not common). Replacement or reprogramming may be necessary. Visually inspect the fuel injector wiring for damage before replacing spark plugs, coil packs,...
Most popular

What kind of engine does a 1986 Chevrolet C10 have?

What kind of engine does a 1986 Chevrolet C10 have? Skully 1986 Chevrolet C10$45,988 (406) 261-8140More Classics @ https://www.classicsas.com/No expense was spared on this one off 1986 C10. Fresh miled 454Ci V-8. Brand new 700R4 Automatic transmissi... More Info › 1986 Chevrolet C10 Short Wheelbase Pickup. VIN: 1GCDC14HXGF371950. 305ci V8 engine. Turbo 350 automatic transmission. Power steering. What was the size of a 1986 Chevy truck? Body The 1986 Chevy pickup truck was a two-door single cab, small pickup truck. It had a capacity of 1,000 to 1,500 lbs., the '86 Chevy trucks didn't have any towing capacity. What was...
Easy tips

Why are some catalytic converters not legal in California?

Why are some catalytic converters not legal in California? The answer is, not enough to qualify for sale in the State of California! In order to be legally sold and installed in California, a catalytic converter must undergo extensive testing to prove that it is durable and meets emission control requirements. What year cars need a catalytic converter? CARB-compliant aftermarket replacement converters are required for California Emissions Certified vehicles, model years 2001 and newer, operated in the state. EPA-compliant converters may be used on vehicles from model years 2000 and older, OR all Federal/EPA-only Emissions Certified vehicles, regardless of model...
Easy tips

What is a TFP valve?

What is a TFP valve? The automatic transmission fluid pressure (TFP) manual valve position switch consists of five pressure switches (two normally-closed and three normally-open) and a transmission fluid temperature (TFT) sensor combined into one unit. The combined unit mounts on the valve body. What happens when a p1810 trouble code is thrown? Whenever the P1810 trouble code has been thrown, the transmissions line pressure is at it’s maximum. That means that all shifts are going to feel incredibly harsh. While it’s not the worst thing in the world for the transmission to run at max line pressure, it still...