Most popular

How can I put my Dodge Ram in 4WD?

How can I put my Dodge Ram in 4WD? You can easily switch into 4WD High (4H) from 2WD High (2H) while moving at speeds up to 40 mph. Or, you can stop your truck, apply the brakes, and shift it while in neutral. To engage the 4H range when on the move, let off the throttle, and then simply push the lever into 4H mode. What makes a Dodge Ram go 4WD or not? In the 2002 to 2008 Dodge Rams, the front driveshaft will always be spinning regardless of being in 4WD because the front axles are unlocked...
Common questions

How do you reset the compass on a Dodge?

How do you reset the compass on a Dodge? need to manually reset the compass. When the vehicle is display CAL until the compass is calibrated. You may EVIC turns off. The compass will now function normally. 1. Turn ON the ignition switch. 2. Press the UP or DOWN button until the Setup then press the SELECT button. 3. Press the DOWN button until “Calibrate Compass” is displayed in the EVIC. Where are the fuse panels on a Dodge Ram? Here you will find fuse box diagrams of Dodge Ram Pickup 1500/2500/3500 1994, 1995, 1996, 1997, 1998, 1999, 2000 and...
Common questions

Is a Greyhound a good pet?

Is a Greyhound a good pet? They can make wonderful pets. Greyhounds are gentle, sensitive and very affectionate dogs, usually forming very close bonds with their owner. With the right socialisation as puppies, they can make good family pets, but will need to be appropriately socialised with smaller pets due to their strong chase instinct. What kind of dog looks like a Greyhound? Afghan Hound The Afghan Hound is one of the most recognizable show breeds due to its elegant sighthound body and long luxurious coat. They basically look like a long haired Greyhound! Afghan Hounds trace their roots back...
Easy tips

What are the torque specs for Dodge 4.7L?

What are the torque specs for Dodge 4.7L? The factory service manual is the only way to go. You can't post conmments that contain an email address. Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence. When to replace cylinder head bolts on Dodge Dakota? Above is the suggested tightening sequence for the cylinder head bolts to avoid premature gasket failure. NOTE: The following torque specs apply to: 2000, 2001, 2002, and 2003 4.7L Dodge Dakota and Durango. IMPORTANT: The cylinder head bolts are ‘ torque to yield ’...
Common questions

What can cause a diesel engine to overheat?

What can cause a diesel engine to overheat? The most obvious cause of engine overheating is if there is any type of issue with the engine coolant. You should perform the following checks since coolant is such a critical part of your diesel’s cooling system. Why is my diesel engine hard to start? The problems that can occur due to the cold weather are well-known and fairly common, such as using summer-grade fuel in winter, a bad glow plug system, slow cranking, or thick, cold oil. However, in summer the problems tend to be quite different. Here are a few...
Easy lifehacks

Can a bad fuel regulator put a Dodge Caravan out of commission?

Can a bad fuel regulator put a Dodge Caravan out of commission? A bad fuel pressure regulator can put your Dodge Caravan out of commission. Here are a few of the most common symptoms of a bad fuel pressure regulator: Misfire – When the fuel pressure regulator fails, it can allow too much or too little fuel into the engine. Either way, this wreaks havoc on the air fuel mixture. What does a fuel pressure regulator do for a caravan? Your Caravan’s fuel pressure regulator controls the pressure of the fuel before it hits the fuel rail. Keeping consistent pressure...
Easy tips

How to replace the instrument panel in a Toyota Corolla?

How to replace the instrument panel in a Toyota Corolla? Remove cowl side trim board rh 34. Remove instrument panel sub–assy lower disconnect the dlc3 connector. remove the hood lock control lever. remove the 3 screws<g> or <h>. remove the 2 bolts<e>. remove the bolt<a> or <b>. remove the bolt<c>. remove the 8 clips and instrument panel sub–assy lower. How to replace dashboard light bulbs on Toyota Corolla? 194LL Bulbs Were Used To Replace Burnt Out Ones. Replacing the burnt out dashboard light bulbs on a Toyota Corolla is something you can do yourself in a fairly short amount of...
Common questions

How do you turn off the slip indicator light on a Toyota Camry?

How do you turn off the slip indicator light on a Toyota Camry? Push and hold the switch while the vehicle is stopped to turn off TRAC and VSC. The TRAC OFF indicator light and VSC off indicator light should come on. Push the switch again to turn the system back on. When to replace light bulbs on Toyota Camry? This article will shed some light on how to replace those worn out instrument panel bulbs. This article applies to the 4th Generation Toyota Camry (1997-2001). Instrument cluster light bulbs, as with any other light bulb, will eventually burn out...
Common questions

How long does it take to replace clutch disc?

How long does it take to replace clutch disc? In the perfect situation, your clutch replacement could take from 4 to 8 hours to complete. Though since most vehicles in need of clutch replacement are not in perfect shape, it can often take between 5 and 10 hours to complete the project, adding more time for less experience on the mechanics part. Is it hard to replace a clutch disc? After that, it's about as straightforward as a job can be -- basically just replace all of your wear parts: flywheel, pressure plate, clutch disc, pilot bearing and throw-out bearing....
Most popular

What causes damage to a flywheel?

What causes damage to a flywheel? Worn starter drive components, worn bushings in the starter, improper shimmed starters on vehicles that use shims, weak batteries and aged equipment cause flywheel problems. Most engines will stop in the same stop each time the engine is shutoff. What do the teeth on a flywheel do? The flywheel has gear teeth around its perimeter that allow the starter motor to engage and crank the engine. Are ring gears hardened? In general technical applications, truck heavy duty engine flywheel starter ring gears teeth is conventionally induction hardened and tempered in order to meet metallurgical...