Easy lifehacks

Why does my car squeak when I take my foot off the brake?

Why does my car squeak when I take my foot off the brake? The noise when taking your foot off the brake may be normal because all parts are new, the squeak noise is most likely caused by the aftermarket brake pads, ( I assume all parts are aftermarket ). Depending on the quality of the pads and the type of brake pad material will determine how quiet they will be. Why does my car make a noise when I change the brake pads? When the brake pads are worn down and need replacing, this metal tab starts to drag...
Easy tips

Does warranty cover accidental damage?

Does warranty cover accidental damage? ', the answer is no. For accidental damage, you will need to make a claim on your car insurance policy. Your vehicle warranty is designed to provide protection for specified mechanical and electrical faults, and it is not intended to cover damage caused by accidents. Does my car warranty cover oil changes? What's Not Covered in a Car Warranty? In general, these items aren't covered in a car warranty: Routine maintenance: Routine oil changes, tire rotations, etc. Wear and tear items: Brakes, brake pads, clutches, windshield wiper replacements, headlight bulbs, etc. What does it mean...
Easy tips

Why does the a / C switch to defrost when accelerating?

Why does the a / C switch to defrost when accelerating? The AC/heater (HVAC) system may unexpectedly switch to the defrost mode when accelerating. This system is operated by engine vacuum and should be inspected for any vacuum leaks if this problem develops. There is also a revised vacuum check valve available to address this concern. How does a Dodge Ram 1500 engine defrost? This involves a 1999 Dodge Ram 1500 Truck with a 5.9 Liter Engine with automatic transmission.Need help to solve this problem. thank you. Air switches from vent to defrost while acceleration or under a load and...
Common questions

Where are the fuses in the Ram 1500?

Where are the fuses in the Ram 1500? The video above shows how to replace blown fuses in the interior fuse box of your 2011 Ram 1500 in addition to the fuse panel diagram location. Electrical components such as your map light, radio, heated seats, high beams, power windows all have fuses and if they suddenly stop working, chances are you have a fuse that has blown out. Where is the ignition fuse on a Dodge? Hi roelcorez, welcome to Just Answer!. Dodge hid one fuse that you probably missed. It's called the ignition-off draw (IOD) fuse, located in the...
Common questions

How do you increase engine idle speed?

How do you increase engine idle speed? Loosen the screw in a counter-clockwise fashion to increase idle speed or tighten it in a clockwise manner in order to decrease the idle speed. Ideally, you will want the idle to rest at 650 RPM. How to adjust idle on Dodge Ram Cummins diesel? Dodge Ram Cummins Diesel Idle Adjustment (Easy!) If playback doesn't begin shortly, try restarting your device. Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. What happens if the idle...
Most popular

Where to put drain bucket on Dodge Caravan CV joint?

Where to put drain bucket on Dodge Caravan CV joint? At this point, it's wise to place a drain bucket beneath the transaxle side of the CV joint connection to catch trickling transaxle fluid that will leak out once the connection of the axle to transmission is separated. How to repair CV drive axle on Dodge Caravan? Rotate the axle by hand until the splines align properly to the groove. Reconnect the remaining components by reversing the procedure. Be sure to torque the hub nut, outer tie rod end nut and ball joint retaining nut to the proper torque specifications...
Easy tips

How can I tell if my car has California emissions?

How can I tell if my car has California emissions? You can identify a CA or Federal vehicle by the emissions system label. Try looking in the door jamb, on the front radiator support, strut tower plate, or under the engine hood. The label will say something along the lines of "This vehicle conforms to... What Year diesel is smog exempt in California? 1997 Your vehicle does not need a smog inspection if your: Gasoline-powered vehicle is a 1975 year model or older (This includes motorcycles and trailers.) Diesel-powered vehicle is a 1997 and older year model OR with a...
Most popular

Is RTV a silicone?

Is RTV a silicone? RTV silicone is a type of rubber comprised of a two-component system and is available in a range of textures from soft to medium (between 15 shore A and 40 Shore). These types of silicones can be cured with a platinum-tin compound catalyst. What is drain plug gasket? What is the Drain Plug Gasket all about? The drain plug gasket seals the drain plug located at the bottom of the oil pan, which holds your vehicle's engine oil. If you have oil leaking from the bottom of the oil pan, it may be the fault of...
Easy tips

When to call a mechanic for a bad transfer case?

When to call a mechanic for a bad transfer case? You notice a fluid leak on the ground, under your transfer case: If you see fluid leaking from the area of your transfer case, call your mechanic as soon as you can to see whether it is safe to drive. It may be less damaging to have your car towed to the repair shop, as opposed to trying to drive it there. What happens when you have a bad transfer case? Your check engine or service 4WD light comes on: The high internal temperatures from a bad transfer case can...
Easy lifehacks

When we fit a spline Where is it typical to place the knots?

When we fit a spline Where is it typical to place the knots? When we fit a spline, where should we place the knots? One potential place would be the area of high variability, because in those regions the polynomial coefficients can change rapidly. How do you use a spline? Draw a SplineClick Home tab Draw panel Spline. Find.(Optional) Enter m (Method). Then enter either f (Fit Points) or cv (Control Vertices).Specify the first point of the spline.Specify the next point of the spline. Continue specifying points as needed.Press Enter to end, or enter c (Close) to close the spline....