Easy lifehacks

Where is the injection valve on a meter?

Where is the injection valve on a meter? Injection valves are mounted at the point of injection to connect the metering line. They protect against backflow and generate a defined back pressure. How does the fuel metering valve work on a fuel pump? To adapt the fuel pressure in the rail, the fuel metering valve on the mechanical fuel pump controls the amount of fuel entering the pump. The plunger is held fully open by a spring to let fuel pass through. What is an ultrasonic chemical injection metering valve? Sign up for news PULSE ultrasonic chemical injection metering valves...
Easy tips

What to do if you have piston failure in your diesel engine?

What to do if you have piston failure in your diesel engine? It is imperative to determine the cause of piston failure and addressing the cause before simply replacing the damaged parts and re-assembling the engine. Otherwise, similar damage will occur shortly after the engine is placed back in service. Diesel engine injection principles and operation What causes a piston to seize in the cylinder? The heat caused by detonation made the piston so hot, the rings stuck and the piston seized in the cylinder. You can see the seizure marks on the side of the piston. This damage usually...
Other

What is Massey Ferguson multi power?

What is Massey Ferguson multi power? With the multi-power system there is one hydraulic clutch pack and also a ratchet type assembly. There is no engine breaking in low multi because of the ratchet clutch. When you move the transmission to high multi it locks up the hydraulic clutch and the hydraulic clutch gear drives another gear. How many horsepower is a Massey Ferguson Super 90? Massey Ferguson Super 90Massey Ferguson Super 90 PowerEngine:77 hp 57.4 kWGas Belt (claimed):60 hp 44.7 kWDrawbar (tested):59.80 hp 44.6 kWPTO (tested):68.53 hp 51.1 kW What Horse Power is a Massey Ferguson 5711? Massey Ferguson...
Common questions

How do you start an old tractor?

How do you start an old tractor? Starting the TractorPlace the gearshift lever in neutral or park.Place all hydraulic controls in neutral.Disengage the power-take-off (PTO).Apply the brakes.Depress the clutch pedal. How did a farmer get his tractor to start? The tractor was not known to start easily, and it is unlikely it started immediately after turning the key. A more likely chain of events was that the victim was holding in the clutch with one hand when he turned the key to start the tractor, and let the clutch out assuming the transmission was in Start (neutral). Can a tractor...
Easy tips

Is the lifting point suitable for safe lifting?

Is the lifting point suitable for safe lifting? Suitable for safe lifting in accordance with the Machinery Directive 2006/42/EC. We advise on customer specific applications and develop tailor-made special solutions. When lifting and securing heavy loads, considerable forces are exerted on the lifting points. Maximum safety is, therefore, essential for preventing injuries and damage. Which is the best lifting point for a safety harness? This design is particularly suitable for transferring heavy loads with lifting points – within an angle of up to 120°. Loads can also be lifted transversely to the axial direction. The PSA eye bolt 900 is...
Easy lifehacks

Are there any cons to an ISX head gasket?

Are there any cons to an ISX head gasket? The rest of the cons are just standard negatives that go with being a truck driver, lack of parking, respect, over regulations, etc. dang, only 30 hours now, I remember when it was 38-42 hours for a isx head gasket, count yourself lucky. and yes it is a bunch of crap to do a head on isx, being a diesel mechanic I know 1st hand. good luck to ya. When did my ISX Cummins blow head gasket? Discussion in ' Trucks [ Eighteen Wheelers ] ' started by Kansas, Mar 8,...
Easy lifehacks

Where does the hydraulic hose go on a Kubota?

Where does the hydraulic hose go on a Kubota? Hi, I have a Kubota L3560. Today I lost power to my grapple and got out to see what was going on and seen fluid spraying out from underneath from one of the hoses. It appears that this hose travels all the way to the back of the tractor. Is it is easy as removing the hose and getting it repaired/replaced and then reconnecting? What kind of hydraulic fluid does a Kubota Tractor use? Kubota UDT Fluid is a multi-purpose, all-weather tractor hydraulic fluid specifically recommended for the Kubota hydraulic, final...
Other

Is the New Holland skid steer l170 safe?

Is the New Holland skid steer l170 safe? I just bought a used New Holland skid steer L170 with 2,000 hours. Sometimes it's fine, but sometimes it just won't start. The safety feature recognizes that I'm sitting in the seat and the belt is buckled, the solenoid clicks but it won't turn over. Anybody know what this might be? I'd take the battery cables off, clean them and tighten . How big is a New Holland LS 170? I recently purchased a 98 New Holland LS 170 from a friend’s friend who was getting out of the construction business. I...
Easy tips

Can a torque converter be rebuilt?

Can a torque converter be rebuilt? The good news is, if it is just your torque converter that is having issues since it's a self-contained unit, you may not need to replace or rebuild your whole transmission. Torque converters can be serviced or replaced as a single unit. Who are the manufacturers of torque converter remanfacture? We have particular rebuild knowledge for the following industrial manufacturer: Allison, JCB, Manitou, Matbro, Case, Caterpillar, Duetz, Fenwick, Ford, Grazzioni, Hyster, Komatsu, Lancer Boss, Massey Ferguson, Mitsubishi, Nissan, Toyota, ZF and Terex. Where can I buy a torque converter for my car? Huge Selection...
Most popular

What year is a 584 International tractor?

What year is a 584 International tractor? The International 584 was a utility tractor built by International Harvester from 1978 to 1985 in the Doncaster, England factory, along with row crop, MFWD, and low profile variations....International 584.Model historyModel introduced1978Model discontinued1985Model statusDiscontinued DiscontinuedPreceded byInternational 574 How many horsepower is a 584 international? International Harvester 584International Harvester 584 PowerEngine:60 hp 44.7 kWPTO (claimed):52.5 hp 39.1 kWDrawbar (tested):46.73 hp 34.8 kWPTO (tested):52.54 hp 39.2 kW Who is International Harvester owned by? International HarvesterIndustryAgricultural, AutomotiveFoundersCyrus Hall McCormick William Deering J.P.MorganDefunct1985FateRenamed as Navistar International CorporationSuccessorNavistar International How do I identify an international tractor? Look all...