Other

Why is my bike only firing on cylinder?

Why is my bike only firing on cylinder? This could be from carbon build up from being way overdue for a plug change, to running too rich, to being oil fouled. Blocked or poorly vented fuel tank. Gas in the tank needs to be replaced by air as it is used, otherwise it creates a vacuum that stops the flow of gas from the tank to the injectors or carbs. What does a motorcycle misfire sound like? So what does a misfire sound like? During a misfire, the engine will make a sudden sound that can be described as popping,...
Most popular

Where is the fuel tank located in a spark ignition engine?

Where is the fuel tank located in a spark ignition engine? FUEL SUPPLY SYSTEM IN SPARK IGNITION ENGINE The fuel supply system of spark ignition engine consists of: (i) Fuel tank (ii) Fuel filter (iii) Sediment bowl (iv) Fuel lift pump (v) Carburettor (vi) Fuel pipes (vii) Inlet manifold In some spark ignition engine, the fuel tank is placed above the level of the carburettor. When does pre ignition occur in a spark ignition engine? Pre-ignition:Burning of air-fuel mixture in the combustion chamber before the piston has reached the top dead centre is called pre-ignition. Pre-ignition occurs when the charge...
Most popular

Can you replace a radiator fan?

Can you replace a radiator fan? Install the replacement cooling/radiator fan motor into the housing. Reinstall the retaining hardware that hold the motor into the housing. Step 3: Reinstall the cooling/radiator fan blade onto the motor. Place the fan blade onto the shaft of the replacement cooling/radiator fan motor. What should I do if my radiator fan is not working? A blown fuse is no big deal, and changing one does not cost a lot of money. If your car’s radiator fan is non-functional, check your car’s user manual and locate the fuse for the radiator fan controller or the...
Easy tips

How close does a key fob work?

How close does a key fob work? Keyless remotes contain a short-range radio transmitter, and must be within a certain range, usually 5–20 meters, of the car to work. When a button is pushed, it sends a coded signal by radio waves to a receiver unit in the car, which locks or unlocks the door. How close should a fob be to a car? The advertised range is 100ft. You must push the button twice within a couple of seconds for it to start, so pocket starting is unlikely. The car won't remote start if the doors are unlocked. After...
Common questions

Is a Dodge 4.7 engine good?

Is a Dodge 4.7 engine good? But in fact, the 4.7L V8 PowerTech is a pretty good engine with simple and durable design. It has a strong cast-iron block and bedplate, a minimum number of electronic systems to fail, and reliable timing chains. What kind of engine does Dodge Dakota 3.7 have? The 3.7 has a 90 degree V-6 design with cast iron block, compacted graphite bedplate and aluminum cylinder heads with single overhead cams on each bank. A centrally-mounted, gear-driven counter-rotating balance shaft, along with a split-pin crankshaft, reduces vibration. What kind of transmission does a Dodge Dakota have?...
Easy lifehacks

Is a ballast resistor necessary?

Is a ballast resistor necessary? So does your application require a ballast resistor? Quite simply, if your distributor has breaker points the answer is yes; if not, the answer is no. See all 7 photos 2 Older points-style ignition system used a single resistor which reduced amperage to the coil resulting in extended life for the coil and points. What happens if the ballast resistor fails to work? If your engine dies as soon as you stop turning the key in the ignition to start it, the ballast resistor could have failed. You can use an ohmmeter to test the...
Most popular

Why is the back hatch on my Dodge Caliber not opening?

Why is the back hatch on my Dodge Caliber not opening? So by now, you should know if the problem was a solenoid or latch handle. If the door still doesn’t want to open, the latch tooth may just be jammed due to a foreign object or misalignment of something. Try pushing and pulling the hatch to loosen it and go through the procedure again. What's the difference between the 2011 Dodge Caliber? The 2011 Dodge Caliber came in six new paint schemes and an improved steering feel. Most trim levels also gained additional functions for the navigation system and...
Other

Why do I get clunks when I put the car in gear?

Why do I get clunks when I put the car in gear? If you don’t have a Camaro or Firebird you could still experience transmission clunks and the causes and fixes are likely going to be the same. So what are those transmission clunks that you hear when you put the car into gear? It’s your drivetrain shifting under load! When your car is at rest the drivetrain is typically relaxed. Why does my transmission make a clunking noise? If your transmission mount or engine mount becomes loose or breaks, you may hear clunking noises whenever you make a sudden...
Most popular

How do you reprogram a 2012 Dodge Caravan key fob?

How do you reprogram a 2012 Dodge Caravan key fob? To program the Dodge Caravan key, you open the driver's side door of your Caravan and press the "Lock" button five times in a row with two seconds of space between each time. Insert the Caravan key into the ignition and turn it one click until you hear the ignition of the chime indicating the key. What to do if your Dodge Grand Caravan key fob is stuck? There is a plastic cap that can be removed to access a release tab if the vehicle won't shift out of Park...
Easy tips

How to reset perform service indicator on Dodge 6.7L?

How to reset perform service indicator on Dodge 6.7L? This bulletin is to aid you on resetting the Perform Service indicator you will find on a Dodge 6.7L with the EVIC displaying this message. PERFORM SERVICE INDICATOR- RESET the “Perform Service” message will display on the EVIC each time you turn the ignition switch to the ON/RUN position to indicate emission maintenance is required. How to perform service message on Dodge Ram? 1. Turn the ignition switch to the ON position (Do not start engine ). 2. Press and release the brake pedal two times. 3. Fully depress the accelerator...