Common questions

What makes a Chrysler 300 engine shut off while driving?

What makes a Chrysler 300 engine shut off while driving? Chrysler's Troublesome TIPM - TIPM seems to be the common failure in all these stalling and engine shut off problems. Read reviews of repair shops in your area. Enter your zip code: Why is my rear camera not working on my Chrysler 300C? Just search for (insert year of manufacture) Chrysler 300C rear camera problem and you'll see the results. There are four possibilities in order from most likely to highly unlikely; a). faulty camera - online research shows that your camera problem is quite common and most of the...
Easy lifehacks

What should the battery voltage be on a 2015 Chrysler 200?

What should the battery voltage be on a 2015 Chrysler 200? With your 200 turned off, you'll connect the negative side of the meter to the negative battery post or wire. Touch the positive side of the voltmeter to the positive battery wire. With the engine off, you should get a reading somewhere between 12.0 volts and 12.6 volts. Is the Chrysler 200 C a good car? I currently purchased a 2015 Chrysler 200 C which all in general is an amazing car with so much to offer for a reasonable price, it's pretty much the Cadillac Escalade of the...
Most popular

Why is my gas pedal harder to push down?

Why is my gas pedal harder to push down? When a gas pedal is hard to press down, an issue with the throttle cable is the most common cause. This issue can be a kink in the cable or the cable not adjusted for the right amount of pressure. If the pressure is too much, this can result in the gas pedal being hard to press. What causes no power when pressing gas pedal? Click to expand... Good question.....if the motor was not revving up and the car won´t move, seems the TPS at the acc pedal assembly, is faulty..but...
Easy tips

What happens if ground wire is disconnected?

What happens if ground wire is disconnected? If the ground is not connected (bonded) to the neutral, or the system ground is not properly grounded to the Earth, two bad conditions will exist: zero voltage will not have a ground reference, which can lead to irregular and inconvenient voltages that could have a negative effect on equipment, but more importantly. What happens when you don't ground a battery? Car batteries can vent hydrogen gas. In theory, a spark could ignite the gas and cause a fire. You'll usually see some sparking as you complete the circuit with the jump leads....
Most popular

What is the booster seat law in Virginia?

What is the booster seat law in Virginia? A child should remain in the booster seat until he/she is at least 8 years of age and 4 feet 9 inches tall. The booster seat requires the use of a lap/shoulder belt and boosts the child to better fit the vehicle seat belt system. How old do you have to be to sit in a car seat in Virginia? Child restraint devices are required for children through the age of seven (until 8th birthday). Safety seats must be properly used and approved to meet Department of Transportation standards. The Virginia law...
Other

How do you remove an old headlight bulb?

How do you remove an old headlight bulb? Remove your old bulb As your wires are disconnected, you are now ready to remove the holder of the headlight first and then remove your old headlight bulb with a proper hold on the base. You also need to rotate the bulb in some cases to free it from the holder. How do you install a new headlight bulb? Install it properly and if it is properly installed, you will never see the rubber gasket. After installing the bulb put back the headlight holder in its old position and also plugs in...
Easy lifehacks

Is a steel oil pan better than aluminum?

Is a steel oil pan better than aluminum? When compared to an aluminum pan, a steel pan holds it shape much better than aluminum and is often salvageable or repairable often times even still while at the track. The image here is of a Canton oil pan for a 351W that was used in rock racing. What metal are oil pans made of? It's bolted to the bottom your engine and is usually made from steel or aluminum. Most oil pans have a pump that rests in the pan to force oil through a filter to move debris, dirt and...
Common questions

How do you know if you have a blown intake gasket?

How do you know if you have a blown intake gasket? This article explains three common symptoms that you may have a bad intake manifold gasket.Misfiring Engine. Engine misfires involve one or more cylinders that fail to produce combustion in a given engine cycle. Difficulty Accelerating. Leaking Coolant. What are the symptoms of a bad intake manifold gasket? Coolant leaks Another symptom of a faulty intake manifold gasket is coolant leaks. Some intake manifold gaskets also seal engine coolant, and if the gasket wears out it may lead to a coolant leak. This may produce a distinct coolant smell, along...
Most popular

Can you tell a 1969 SS Nova from a clone?

Can you tell a 1969 SS Nova from a clone? The problem with the SS, though, is the fact that few authentic Super Sports were actually produced, leading to many inauthentic SS clones flooding the classic car market. But spotting an SS clone is actually pretty easy, so long as you are willing to learn how to decode VIN numbers and research the Nova's SS options. Determine the engine type. What was the last year of the 1970 Nova? The 1970 Nova Super Sport was the last production model year that featured the 396 big block high performance engine. From...
Common questions

What was the rear bumper of a 1975 Corvette made for?

What was the rear bumper of a 1975 Corvette made for? The rear bumper received inner shock absorbers to reduce damage in the event of an impact condition. The 1975 Corvette featured new front and rear bumper assemblies. What's the difference between a 1974 and 1975 Corvette? The 1975 Corvette featured new front and rear bumper assemblies. Lastly, the rear bumper fascia was molded as a single urethane plastic component, unlike the 1974 model which featured two separate urethane assemblies that mated down the centerline of the car. Who was the Chief Engineer of the 1975 Corvette? David McLellan replaced...