Easy tips

How big is a 1989 champion transvan Van?

How big is a 1989 champion transvan Van? It's a 1989 Champion Transvan van with 98k miles that I had plans to gut and build out but health problems got in the way. Based on a Ford E350 Dualie chassis, it's 20 feet long so it fits in parking spots, but it's wide enough to sleep cr 1979 Dodge Briugham transvan. RV - $5,000 (Los Angeles) How much does a transvan RV cost to sell? The van has a lot of new parts: new brakes, tuneup, carburetor overhaul, fuel pump, tires. The van has a small couch, dining table, 2...
Most popular

What to do with a rotten front end of a caravan?

What to do with a rotten front end of a caravan? Rot on the off side. So the decision was made to completely gut the front end. Rotten wood cut back & new battens bonded in on the nearside. Rotten timbers replaced on the off side around battery box. A complete new front frame was made from scratch. How to fix automatic sliding door on Dodge Grand Caravan? My wife came home and said the door on our grand caravan was not opening and closing automatically but would work Manually. The easiest thing for me to do was check for...
Most popular

Where are the lower control arms on a Chrysler 300C?

Where are the lower control arms on a Chrysler 300C? Therefore, the arms that run from the knuckle toward the front of the car are the “tension struts”, and the arms that run from the knuckle directly inward toward the middle of the car with the shocks attached to them are the “lower control arms”. See this pic for clarification… Okay, now with that out of the way. Where are the tension struts on a Chrysler 300C? These tension struts are simply held on by one bolt and nut on the front cradle part, and one ball joint stud and...
Most popular

What causes a vibration in a Dodge Dakota?

What causes a vibration in a Dodge Dakota? Let us know in the Values & Prices Paid section! My daughter's 1990 Dodge Dakota with the 3.9 L engine and automatic transmission with overdrive has developed a vibration. It happens when accelerating while in gear. If the gear selector is set to neutral while rolling, and the engine rpm is speeded up, the vibration doesn't occur. What's the speed of vibration on a Dodge Ram? Dodge Ram with vibration between 45 and 55 MPH. Had drive shaft rebalanced, and it helped a little. > FREE expert answers to automotive questions Complaints...
Easy tips

Is there a problem with the Jeep Grand Cherokee 5 diesel?

Is there a problem with the Jeep Grand Cherokee 5 diesel? Diesel Engine problem of the 2015 Jeep Grand Cherokee 5 Failure Date: 09/17/2019 Since the recall a year ago (spring 2019) the vehicle has a serious hesitation in the throttle response until the ecodiesel engine reaches full operating temperature. This creates a serious safety hazard. Why is my Jeep Grand Cherokee not washing? 4. Dealerships unable to clear check engine light and blame issues on the fact this unit has a diesel engine. Local waterway car wash is refusing to wash these vehicles due to rapid and unattended acceleration...
Most popular

How many amps does an O2 sensor use?

How many amps does an O2 sensor use? Amperage values can be from approximately 1.5 amps at ambient temperature to 200 milliamps at full operating temperature. If engine performance checks or scan tool data suggest a potential O2 sensor malfunction, don't forget the basics. Always conduct a visual inspection of the sensor, electrical connections and wires. What does post cat O2 sensor do? The pre-catalytic converter oxygen sensor is used for fuel trim and the post-catalytic converter oxygen sensor is used to monitor converter efficiency. How do you test an oscilloscope with an O2 sensor? Using an appropriate connecting device,...
Other

What does a transmission fluid temperature sensor do?

What does a transmission fluid temperature sensor do? The Transmission Fluid Temperature sensor measures the temperature of the transmission’s oil (AFT). Its primary function is to inhibit overdrive and converter clutch operation when cold. On some models, it also inhibits certain gears based on the temperature (too hot or too cold). When does the coolant temperature sensor need to be replaced? Noted below are a few of the warning signs that will alert you that the coolant temperature sensor is damaged and needs to be replaced. The engine is getting poor fuel economy: when the coolant temperature sensor is not...
Other

What does a p2099 Bank 2 sensor mean?

What does a p2099 Bank 2 sensor mean? A P2099 code means that the post catalytic converter O2 sensor on bank 2 has detected a rich exhaust condition. Fuel efficiency may be compromised and the code should be addressed as severe. Symptoms of a P2099 code may include: Other related diagnostic trouble codes may be stored Why does my engine have a trouble code of p2099? Some potential causes of this trouble code may include: The air inlet tubing connected to the intake manifold could have a vacuum leak allowing unmetered air to enter the engine Anything that could cause...
Easy lifehacks

Does an oil change include tire rotation?

Does an oil change include tire rotation? Changing your oil and filter will help your vehicle's engine continue working at its best. All oil change packages include a tire pressure check, fluid top off, tire rotation, visual brake check, standard oil filter and our 23-point inspection. Is it normal to have a check engine light after oil change? Oil changes are essential maintenance for your car but it won't do anything that could trigger your check engine light to come on. If you notice the light after an oil change, something else is wrong. What happens if I don't rotate...
Common questions

What is the code for the crankshaft position sensor?

What is the code for the crankshaft position sensor? If there’s already an RPM signal, wiggle the wiring harness so try and induce the fault. This code is very similar to P0385, which refers to Crankshaft Position Sensor “B”. Other related crank sensor error codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389. How to test a crankshaft position sensor using a multimeter? Set your digital voltmeter to a low range on the AC voltage scale. Connect your meter leads to the sensor pins. Make sure to keep your meter lead wires...