Common questions

What do you need for a trailer turn signal?

What do you need for a trailer turn signal? On the trailer side you will want to make sure the connector is clean and that the main ground is connected to a clean and corrosion free bare metal surface. You will also need to do the same for each of the trailer lights. Why does my trailer blink when I Turn Left? What you are describing is normally the result one 1 of 3 issues: First, there could be some corrosion in or on the connectors on the vehicle or trailer side or both. Second there could be a bad...
Easy tips

Do all EVS have regenerative braking?

Do all EVS have regenerative braking? Regenerative braking is now in nearly every forerunning electric vehicle on the market today. Flash forward to 2020 –– regenerative braking is widely available in a vast range of alternative energy vehicles. From the inconspicuous Honda hybrid to the fully electric battery-run cars like the Tesla Model 3. What is brake energy regeneration? Regenerative braking is a way of taking the wasted energy from the process of slowing down a car and using it to recharge the car's batteries. On a normal car, braking simply wastes energy - but with regenerative braking, some of...
Other

How many fuel filters does a 6.0 have?

How many fuel filters does a 6.0 have? two fuel filter elements The 6.0L and 6.4L Power Stroke is equipped with two fuel filter elements. The larger, primary fuel filter is located inside of the left hand frame rail, below the driver's side floorboard, with the fuel pump. How many fuel filters does a Kubota BX25D have? It has 3 fuel filters in series, a primary, secondary and a final. All are big size filters. They wanted the fuel to be clean! Still starts easily and runs like a top. How much oil does a case 1845C take? 1845C hydraulic...
Most popular

How can leak oil be harmful?

How can leak oil be harmful? In addition to their environmental impacts, oil leaks can lead to major damage to your vehicle's engine, as well as to its radiator and HVAC system. Accumulated oil can degrade the rubber hoses and seals used in these components and cause them to wear out prematurely. Oil leaks are also a fire and safety hazard. Is the Cat C9 a good engine? The C9 showed excellent startability and the power to pull 6-percent grades in soft dirt. First gear was sufficient to overcome inertia for the Sterling LT9500, equipped with an Eaton Fuller 11908LL...
Easy tips

Can you get a Cummins in a Ford?

Can you get a Cummins in a Ford? So, yes, Ford has installed Cummins engines in their trucks. Caterpillar engines too. Yes, Ford used Cummins Diesel engine in their medium duty and heavy duty trucks. Cummins engines were installed in Ford's heavy duty F650/F750 line of trucks. When did the 8.3 liter Cummins engine come out? Cummins ISC, QSC, and 6CTA 8.3L Parts. Show/Hide Details. The Cummins C Series was introduced in 1985 with the 6C 8.3 liter engine. More durable that other models, this inline, 6-cylinder, medium-heavy duty engine was designed to last 150,000 miles between overhauls. How much...
Common questions

How many Seperator hours on your 2388 problem?

How many Seperator hours on your 2388 problem? The good part the dealer has always had the parts.My son said maybe we should demo a JD at this rate we might.Hope it can make a full day tomorrow so we can finish corn. How many seperator hours are on your 2388. Why does my 2388 Auger not shut off? The unloader on the 2388 often won't shut off when under load (filling truck/wagon to the top and need to shut off mid stream). The light goes out, but the auger keeps running. Last night, I noticed that the light would...
Common questions

Can you weld aluminum with a millermatic 250?

Can you weld aluminum with a millermatic 250? Subject: RE: Using a millermatic 250 to weld aluminum? You will want straight Argon for aluminum, 30A should be correct for spool gun, you will need the 14 pin connector / card as posted above for the welder. I use more 5356 wire than 4043, as the 5356 has better strength in the weld. How many amps is a Miller 250 welder? How many amps does a millermatic 252 draw?TitleMillermatic® 252 MIG Welder - 200(208)/230VRated Output200 Amps at 28 VDC, 60% duty cycle,250 Amps at 28 VDC, 40% duty cycleMax Open Circuit...
Most popular

How do you Regen a Kenworth PACCAR mx-13?

How do you Regen a Kenworth PACCAR mx-13? Every time this process is interrupted you will have to start from the beginning.” The following steps are recommended for a parked manual regen: Maintain a minimum of 5 feet of clearance to any combustible materials from the edge and top of the vehicle Push the button for 20 seconds to start the regen – the truck’s RPMs should raise. What does a Kenworth T660 wiring diagram do? Kenworth T660 Wiring Diagrams | Wiring Library – Kenworth Wiring Diagram Pdf The diagram provides visual representation of a electric structure. However, this diagram...
Common questions

How big is a 427 block on a tall deck?

How big is a 427 block on a tall deck? As has been stated, .4" longer rods (6.535" long) and you can use regular car pistons in a tall deck. The longer rods cost no more than the typical aftermarket stock length rod. The 427 block has a bore of 4.25" and a stroke of 3.76". What's the stroke on a tall deck 427 Chev? The longer rods cost no more than the typical aftermarket stock length rod. The 427 block has a bore of 4.25" and a stroke of 3.76". Usually these blocks can go .06" overbore with no...
Common questions

When did John Deere 7720 Titan II come out?

When did John Deere 7720 Titan II come out? 1988 John Deere 7720 Titan II combine w/ 5,250 ind. hrs., bin extension, chopper was rebuilt and used 1 season, new cab interior foam kit, long unloading auger, Ser. #630530. Also comes with spare tire & gear box for JD 643 corn head.. Where is the John Deere Titan II Chopper located? 1988 John Deere 7720 Titan II Combine, Runs and Operates, Has rear Chopper by needs fixed, Located by Wakefield, Nebraska. 1988 John Deere 7720 Titan II combine w/ 5,250 ind. hrs., bin extension, chopper was rebuilt and used 1...