Common questions

How do you adjust the clutch on a Ford Mondeo?

How do you adjust the clutch on a Ford Mondeo? Fordtech. There is an adjusting nut/locknut at the gearbox end, you need to tighten to raise the pedal off the floor. Clutch pedal should be just a little higher than the brake. If it's still not right, the problem's not adjustment. Where can I get a clutch replacement in the UK? Check out the ClickMechanic price for a Ford Mondeo Clutch replacement in the UK. You can book online and the mobile mechanics on our network will come and do the work on your doorstep, one way to make your...
Common questions

When did Mustangs get the 302?

When did Mustangs get the 302? The Mustang Boss 302 is a high-performance variant of the Ford Mustang originally produced by Ford in 1969 and 1970, alongside its more powerful sibling the Boss 429 Mustang. Ford revived the name for another two year production run in 2012 and 2013. When did Ford start the 302 engine? Starting its run in 1968, Ford's 302 entered several of its models and for 27 years it reigned supreme.In the 1980s it was known as a 5.0-liter displacement engine, even though it was 4.9-liters. What was the year of the 1968 Mustang? 1968 Mustang....
Easy tips

What are the torque specs on a small-block Chevy?

What are the torque specs on a small-block Chevy? Small Block Chevy Torque SpecsFastener TypeTorque Spec7/16 in. Inner Main Cap Bolt70 ft.-lbs.3/8 in. Outer Main Cap Bolt40 ft.-lbs.11/32 in. Connecting Rod Bolt38-44 ft.-lbs.3/8 in. Connecting Rod Bolt40-45 ft,-lbs. What kind of engine does a 1958 Chevy Bel Air have? gasoline (petrol) engine with displacement: 3859 cm3 / 235.5 cui, advertised power: 101.5 kW / 136 hp / 138 PS ( SAE gross ), torque: 277 Nm / 204 lb-ft, more data: 1958 Chevrolet Bel Air Sport Sedan Six (man. How much torque does a small block Chevy have? Small Block...
Common questions

What causes hesitation in a carbureted engine?

What causes hesitation in a carbureted engine? Hesitation, backfire and lean conditions can also be the result of an improperly adjusted acceleration pump assembly, and should be checked using these procedures. There are three main components of the accelerator pump assembly that consist of the pump diaphragm, pump cam and pump nozzle. How to fix engine hesitation when the throttle is depressed? Step by step guide on how to repair an engine hesitation when the throttle is depressed, this information pertains to all internal combustion engines. Protective eye wear and gloves. Begin by parking the vehicle on level ground, in...
Other

How do you calibrate a GM speedometer?

How do you calibrate a GM speedometer? GM Speedometer CalibrationUsing Gear/Tire wizard in VCM Editor (Edit> Gear/Tire Wizard) Insert your new tire and gear in the columns on the right. When you have entered the correct values for your vehicle click the "Adjust" button. How do you change the gear on the speedometer? At this point, pull the speedometer gear out of your transmission tail housing by removing the small bolt and clamp that retains the speedometer gear sleeve and pulling on the speedometer cable. Then count the teeth, subtract or add to the number of teeth and select a...
Common questions

Are there different engine colors for Oldsmobile Cutlass?

Are there different engine colors for Oldsmobile Cutlass? Lots of folks will tell you that GM did not pay much attention to color matching engine paints, but GM requirements for engine colors were the same as for external body colors. If you look at original cars, you will see the engine colors did not vary any more than the exterior colors did, which was very little. What are the parts numbers for Oldsmobile Cutlass 442? Oldsmobile Cutlass 442 Hurst/Olds Restoration Parts. Shop over 6500 part numbers for your restoration project. 1964 thru 1988 Oldsmobile Cutlass, 442, Supreme, Hurst Olds, F85,...
Common questions

What are the different parts of a piston?

What are the different parts of a piston? As mentioned before, most vehicle engine pistons feature three rings; two upper compression rings and a lower oil ring. For clarity, the different rings are explained below. Compression ring – this is the top side ring and nearest the combustion chamber. Where do I get the best IMD Pistons? IMD Pistons, Established 1989, provides high quality pistons, rings, gaskets and rebores. We are based in cheshire, and operate on a worldwide basis. With over 6000 reviews on eBay, we have many affiliates, and if you need any more information, please do not...
Other

Are there exact reproduction spark plug wire sets?

Are there exact reproduction spark plug wire sets? Exact Reproduction Sets. In order to satisfy the most discriminating enthusiast and restorer, Lectric Limited manufactures USA-made authentic reproduction spark plug wire sets. These sets are identical to the spark plug wires as they would have appeared on your vehicle when it shipped from the factory. What was the color of the spark plugs? Wire Script Color: original script ink type and color (white, black or yellow). Wire Braiding: original machine-applied metal braiding (only 1965-74 Corvette big block with radio). When was spark plug wire 3-q-62 made? This code (3-Q-62), means that...
Common questions

Is there a 1969 Mustang 428 Cobra Jet engine?

Is there a 1969 Mustang 428 Cobra Jet engine? Rare Mustang GT Concours nut and bolt rotisserie restoration 1 of 50 Q-Code 428 Cobra Jet convertibles built 1 of 20 Q-Code 428 Cobra Jet convertibles equipped with a 4-speed 1 of 9 Q-Code 4-speed 428 Cobra Jet convertibles with ... Is the Ford Mustang Mach 1 428 a muscle car? ©2007 Publications International, Ltd. With 59 percent of its weight over the nose, a Mach 1 428 Cobra Jet struggled fortraction, but looks, power, and personality made this a Ford muscle car classic. But the Cobra Jet's most-pertinent product was...
Most popular

Why does my rear suspension make a knocking noise?

Why does my rear suspension make a knocking noise? There are several things that could be causing the knocking sound from the rear suspension. My first guess was worn out bushings allowing metal-to-metal contact, broken sway bar end-links, or worn out shock mounts (top or bottom). If you can, pop the rear tire off and inspect the suspension mounts for cracked rubber or worn out parts. Why does my rear differential make a whirling noise? Rumbling and whirring noises at speed over 20 mph, moreover, can be the result of worn carrier bearings. For vehicles with C-clip axles, the rear...