Most popular

How to repair a Ford Fusion PCM ECU?

How to repair a Ford Fusion PCM ECU? This factory Ford Motorcraft kit includes six... This is a Ford Fusion PCM (Powertrain Control Module) repair service for a 2006, 2007, 2008, or 2009 Ford Fusion 3.0L V6 that has been damaged by a failed ignition coil. This is the most common problem with the PCM... How do you turn off the ECU on a Ford? Install the plug-in inline flasher — which resides on a chip in a special wire. Locate the control wire from the ECU to the engine. The car needs to be off when you plug the...
Common questions

How does a Ford Ranger keep it cool?

How does a Ford Ranger keep it cool? While going down the road the movement of air through your Ranger’s radiator will usually be enough to keep it cool, without the help of the fan. It’s when you are hardly moving that the radiator fan is going to do the work of keeping air flowing into the radiator. Why is my Ford Ranger not blowing air? I tore into the dash but could only get to the servo for the heat/cold blend door. I pulled the blower motor, which is working correctly, and cleaned out a wasp nest, dirt-dobber (?)...
Other

How do you replace wheel bearings on a Ford Escape?

How do you replace wheel bearings on a Ford Escape? Pull the cotter pin from the axle shaft with your pliers. Pull off the washer from the axle shaft with your hands. Loosen and remove the large central axle nut with your 30 mm deep socket, 1/2-inch ratchet and breaking bar. How do you remove the axle from a Ford Escape? Loosen and remove the large central axle nut with your 30 mm deep socket, 1/2-inch ratchet and breaking bar. Loosen the lug nuts on the wheel. Raise the Ford Escape until the wheel is off the ground. Set a...
Common questions

How does EXUP valve work?

How does EXUP valve work? This is a system that employs a variable EXUP valve in the muffler that can change the configuration of the exhaust duct in a way that controls fluctuations in exhaust pressure at the moments of overlap between the intake and exhaust valves in order to improve intake efficiency, boost power output and improve fuel ... What is an EXUP valve? The EXUP system was a four-stroke power valve system, placed in the bottom-end of the exhaust's downpipes to fool the pipe into thinking it was the best 'length' for both mid-range and high-rpm operation. You...
Most popular

Why is my car jumping out of 2nd gear?

Why is my car jumping out of 2nd gear? The gear is not fully engaged, and has tension on the shift fork while driving. Sometimes it will pop back into neutral. Really worn motor/transmission mounts can also cause intermittent popping out of gear. If the synchronizer is completely toast, it may not be able to hold the gear in engagement. How does a manual transmission work on a Mustang? Automatic transmissions use fluid pressure to select gears and electronic sensors to decide which gear your Mustang should be in. Manual transmissions are mechanically operated with the force of your hand...
Most popular

What kind of coolant does a Ford Taurus 2001 take?

What kind of coolant does a Ford Taurus 2001 take? Prestone 50/50 Coolant/Antifreeze. What kind of coolant does a 2001 Toyota Echo take? Pentosin 1 Gallon Red 50/50 Antifreeze. What kind of coolant does a 2000 Ford f150 take? Zerex 1 Gallon Orange 50/50 Coolant/Antifreeze. What kind of coolant does a 2002 Ford Taurus take? The 2002 Ford Taurus most recommended coolant is Prestone, yellow 50/50 pre-diluted coolant or antifreeze. How much coolant does a 2001 f150 take? The 2001 Ford F-150 5.4Coolant capacity is 25 quarts. If You need to do a coolant change on the vehicle then You...
Easy lifehacks

What happens if you have a bad exhaust manifold?

What happens if you have a bad exhaust manifold? If the exhaust manifold cracks, breaks, or leaks, it can cause an exhaust leak that will lead to a noisy exhaust. The vehicle may produce a hissing or tapping sound from the engine bay that may get louder when the engine is accelerated. What is the purpose of an exhaust manifold? Exhaust Manifold The exhaust manifold is a tube for removing the exhaust gases away from the engine cylinders. It collects exhaust gases from the exhaust ports of the various cylinders and conducts them to a central exhaust passage. Constructional Details...
Easy lifehacks

Do you need to replace timing belt with water pump?

Do you need to replace timing belt with water pump? Generally, the idler pulleys, tensioner and water pump should always be replaced when the timing belt is replaced. In most cases, the timing belt drives the water pump, so it is the right time to replace the water pump. It is also recommended by the manufacturer. WORD TO THE WISE. Should I replace the water pump at the same time as the timing belt? If that is the case, then it is advisable to replace the water pump & auxiliary drive belt at the same time as the timing belt...
Most popular

How do I remove the wiper blades from my windshield?

How do I remove the wiper blades from my windshield? Wiper Blade Removal Instructions. Park your windshield wiper blades in the middle of your windshield by turning off your car when the wiper blades are in the middle of the wipe cycle. b. Lift the wiper arm off of the windshield. c. To remove the old wiper blades from a J-hook arm, depress the button tab on the connection adapter clip and pull... Where does the Pin go on a windshield wiper? This means that the wiper blades attaches to the wiper arm with a has a pin or clip....
Easy lifehacks

How much does a Ford 6.0 diesel engine weigh?

How much does a Ford 6.0 diesel engine weigh? 6.0L Power Stroke SpecsEngine:6.0L Power Stroke diesel V-8 (based on the International VT 365)Oil Capacity:15 quarts w/ filterEngine Weight:Approx. 966 lbs w/ oilEmissions Equipment:Exhaust gas recirculation (EGR) and diesel oxidation catalyst (DOC)Peak Horsepower:325 HP @ 3,300 RPM How much does a 6.0 motor weigh? These engines weigh about 1,100lbs. How much does a Powerstroke engine weigh? The Power Stroke is an electronically controlled, direct injection engine with a 4.11 in × 4.18 in (104.4 mm × 106.2 mm) bore and stroke creating a displacement of 444 cu in (7.3 L). It...