Common questions

Why is my defrost not working on my Dodge Ram?

Why is my defrost not working on my Dodge Ram? Defrost is a safety issue there needs to be a recall.. The fan motor was making a noise similar to the sound that was made when you would put playing cards in the spokes of your bike. Took to dealership they claimed they had to replace the motor when I knew that was not the problem. What to do if your Dodge Ram heater is not working? When your heater is not working it can be a challenge to determine the cause. It may make the most sense to take...
Easy tips

What kind of gas does a Dodge Ram 1500 take?

What kind of gas does a Dodge Ram 1500 take? A Dodge Ram 1500 uses regular gas. But Ram recommends an 89 octane for the V8 engine, which is a mid-grade gas. However, the V8 will also run on regular gas as well. And, Ram recommends regular gas for the 3.6L (219.9 ci) V6 engine. Can you put premium gas Ram 1500? Ram recommends 89 Octane. Now putting a lower octane than recommended is a very bad idea. Your Alfa and many other cars were tuned for the higher octane and using a lower octane fuel will cause pinging (pre-detonation)...
Most popular

Will a car start without oil pressure?

Will a car start without oil pressure? The oil pressure switch on newer model vehicles will signal its computer, which can cause a car not to start if it has low oil pressure. What happens if you have low oil pressure in a Dodge Caravan? One of the most serious issues that can happen to your Dodge Caravan ‘s engine is if it ends up with low oil pressure. Low oil pressure will cause the engine to seize up. When the oil pressure light on, it should be assumed that the engine locking up is imminent. Can a low oil...
Other

How does a speed boat speedometer work?

How does a speed boat speedometer work? A speedometer on a boat works by using a pitometer. The pitometer works by comparing how fast your boat is going against the speed of the water you're travelling on. This works by measuring the speed of water coming into a tube compared to air pressure to give an estimated speed figure. How can I Fix my Mercury speedometer reading? This problem is easy to fix with one simple tool a drill bit. Locate the tiny hole on the leading edge of your lower unit. This is where water is forced in and...
Common questions

How to reset the Check Engine light on a Ford F 250?

How to reset the Check Engine light on a Ford F 250? Turn the OBD tool on, using the power switch on the tool. Turn the ignition key to the "II" position and wait for the check engine light to go off. This will reset the error codes and the light. I am a Registered Financial Consultant with 6 years experience in the financial services industry. How do you remove a dash panel on a Ford? Determine which panel you need to remove and slide your fingers into the air vent located in that panel. If you are removing the...
Common questions

What does a torsional damper do?

What does a torsional damper do? The purpose of using a torsional damper is to keep engine torque peaks as well as operational irregularities away from the powertrain and connected units. What are the springs in a clutch plate for? The facing springs lie between the clutch facings. They ensure gentle clutch engagement and hence smooth take up of drive. The pressure plate of the clutch must at first press the clutch plate against the flywheel, acting against the spring load of the facing springs. How does a damper plate work? Damper plates used in the marine industry are designed...
Easy lifehacks

Do Ford Rangers have hydraulic clutches?

Do Ford Rangers have hydraulic clutches? The hydraulic clutch on a Ford Ranger uses brake fluid to pressurize the clutch system and makes it easier to disengage the clutch from the transmission. Before doing any service work, you need to diagnose the hydraulic clutch on your Ford Ranger. How does the hydraulic clutch work on a Ford Ranger? The hydraulic clutch on a Ford Ranger uses brake fluid to pressurize the clutch system and makes it easier to disengage the clutch from the transmission. If the clutch system runs out of fluid or the system runs low on fluid, the...
Common questions

How to check and set up base ignition timing?

How to check and set up base ignition timing? Step 1. Following all manufacturer’s directions, carefully install a timing light on the cylinder #1 spark plug wire. Use all due caution here, as secondary ignition voltage can be as high as 100,000 volts or more. Also ensure that the timing light’s cords can not get tangled in a moving engine or burned on hot components. Step 2. What's the default ignition timing for a rotary engine? The value we enter here will be a static value that our MegaSquirt will use to command ignition timing. 10.0 is the default, and...
Most popular

What kind of engine does a 1968 Ford Mustang have?

What kind of engine does a 1968 Ford Mustang have? Introducing Kash and Kars. The book that has every motorhead and classic car junkie begging for more! Available in e-Book, and paperback wherever books are sold. A choice of four different engines. 200 c.i. @ 115 h.p. w/8.8:1 compression and a one barrel carburetor. Engine code ‘T’ 289 c.i. @ 195 h.p. w/8.7:1 compression and two barrel carburetor. When did the Ford 289 engine come out? Introduced in the late 1965 model, the 289 was a peppy little engine. The 289 cubic inch engine was Ford's V8 90 degree overhead...
Easy lifehacks

What is the difference between a 351 Windsor and modified?

What is the difference between a 351 Windsor and modified? Windsor valve covers use 6-bolt covers, whereas the Cleveland/Modified uses 8-bolt covers. Timing Chain. Cleveland/Modified engines have the timing chain recessed into the front of the block itself, and its timing cover is essentially just a flat piece of metal. When was the Ford 351 Windsor engine made? The 351 Windsor (351w for short) is the largest of the Ford Small Block engine family. Ford Motor Company built them between 1969 and 1996. It’s a 90 degree V8 with an overhead valve train. Is the 302 similar to the 351...