Easy lifehacks

Will pulling horn fuse Stop alarm?

Will pulling horn fuse Stop alarm? The alarm will shut off when you remove the fuse. Try reinstalling the fuse with the same tool. The alarm should stay off. If it comes back on, pull the fuse out and call a mechanic for an appointment to have the system repaired. Why does my car horn keep going off? My horn keeps going off intermittently. Some times it is a long honk and other times it is several short honks. Why is it doing this? Where is the fuse for the horn? Where do I find the fuse box for my...
Common questions

Why won t my ram 2500 start?

Why won t my ram 2500 start? While there are a variety of reasons your Dodge Ram 2500 won't start, the most common 3 are a dead battery, an alternator problem, or failed starter. Why does my Dodge Ram not start when I turn it on? It’s the battery - Chrysler is notorious for this.. something along the lines of if not enough voltage it won’t even attempt to crank. grizzstang and Dhill29 like this. Yes, it was at 81 percent and the dash would flicker but wouldn't make a sound when you turn it over. Still not sure what...
Most popular

What is the break in period for a new Ram 1500?

What is the break in period for a new Ram 1500? Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. When did RAM switch to 8speed? 2012 The Chrysler Group to be exact. Their TorqueFlite 8 speed automatic transmission, introduced in 2012, currently exists in select Dodge, Chrysler, Jeep and Ram models and there are plans for its existence to spread even larger...
Easy lifehacks

What causes the p0171 code on a Ford Ranger?

What causes the p0171 code on a Ford Ranger? Vacuum Leaks – With the Ford Ranger, one of the most common cause for the P0171 code to show is a vacuum leak. Take a look around and see if you can find the vacuum leak. What is the trouble code on my Ford Ranger? P0171 Ford Ranger. September 10, 2018. One of the most common trouble codes with the Ford Ranger is the P0171 code. This code number references a number that is given to you when you plug your car into a OBDII scanner. What do the p1131 p1151...
Other

What happens when the electronic throttle warning light comes on?

What happens when the electronic throttle warning light comes on? Some times after the electronic throttle warning light comes on the vehicle pits, sputters and shakes. Most times it either just quits running or will not go over 20 mph. If I stop and put vehicle in park, turn it off and restart it, the electronic throttle warning light and the ABS warning light go out, but the check engine light stays on. When to cycle the ignition key on a red lightning bolt? This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a...
Easy tips

How long should a key fob last?

How long should a key fob last? Every time that a driver wants to use their key fob, the battery will have to produce the electricity that is needed to power it. A key fob battery will usually last around three to four years before it will need to be replaced. Not having a fully functional key fob can lead to a lot of frustration and stress. Do you need key fob for Dodge Ram 3500? Buy your next DODGE RAM keyless entry remotes and save up to 75% off dealership prices on key fobs for RAM 1500, RAM 2500...
Other

How do you reset the Uconnect on a 2010 Dodge Ram?

How do you reset the Uconnect on a 2010 Dodge Ram? Five Easy Steps to Reset UConnect®Ensure your vehicle is in park and in “Run” mode.Press and hold down the volume and tuner knob buttons at the same time.Hold down the knobs for 10 – 20 seconds.After holding down the knobs, the screen should flash your vehicle brand name and then go dark. How do I reset my Uconnect Radio 1500? To begin, turn Your ignition on, but You don't need to start the engine. Now go to the Uconnect screen and hit the button at the bottom that says...
Easy lifehacks

How are engine blocks and cylinder blocks remanufactured?

How are engine blocks and cylinder blocks remanufactured? The second step in the engine block remanufacturing process is to magnaflux the entire remanufactured engine block. We magnaflux with Androx 9704 and check under a blacklight for cracks and structural imperfections. If the used engine block has significant cracks that can’t be welded it is deemed unfit to be a remanufactured engine block. Can a cylinder head be removed from a car? Air leaking from the intake suggests an intake valve or seat fault. Removing the cylinder head is relative straight forward. However, care will need to be taken and the...
Most popular

Can a car diagnostic test trigger a check engine light?

Can a car diagnostic test trigger a check engine light? This means that a car diagnostic test does a system analysis that reads the error codes from your check engine light in layman’s terms. With that said, many errors will not trigger a check engine light. With this in mind, it’s not a bad idea to get a car diagnostics checkup periodically. Where do I find the Check Engine Light code? Then, press the “read” button on the scanner to access the check engine light code. The code will be a series of letters and numbers. Record all of the...
Easy tips

Why wont my key turn in my Dodge Ram?

Why wont my key turn in my Dodge Ram? While there are a variety of reasons your Dodge Ram 1500 key won't turn, the most common 3 are a binding steering column/lock, an ignition switch issue, or a problem with the ignition key. Why does my GM ignition key not turn? Sometimes the ignition key won't turn or rotate. If that happens the vehicle won't start, the steering wheel won't turn and it won't shift into gear. On a late 90's or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler....