Common questions

How do you adjust a clutch throw?

How do you adjust a clutch throw? To adjust, simply pull up on the clutch cable and loosen the locknut and the adjuster nut slightly. Next, slowly pull up on the clutch cable again. You will feel a point where the clutch fork engages. This is where the clutch cable should be adjusted to. How do you change the clutch on a Dodge Dakota? Rent a tranny jack. Buy a manual, if you don't all ready have one. Read the clutch replacement section completely, and then re-read it a couple of times. Assemble the necessary parts & tools. You will...
Easy tips

Which is better for fuel economy Cummins or Ho?

Which is better for fuel economy Cummins or Ho? There's gonna be myriad reasons for a buyer to select a HO equipped truck over the standard output Cummins but fuel economy is not likely to be anywhere near the top of that list. How much oil does a Cummins 5.9L have? 3rd Generation 5.9L Cummins Specifications 3rd Gen 5.9L Cummins Years: 2003-2007 Emissions Controls Oxidation Catalytic Converter Weight: 1150 Lbs Dry Engine Oil Capacity: 12 Quarts or 11.4 Liters /w Filters Coolant Capacity: 32.7 qt or 30.9 Liters When did the 3rd generation Cummins truck come out? When the 3rd...
Easy lifehacks

Can a crankshaft sensor cause misfire?

Can a crankshaft sensor cause misfire? Engine Misfiring and Stalling A faulty crankshaft sensor will cause your engine to misfire as incorrect fuel injection readings weigh in. When this problem becomes especially apparent, the engine may stall and have difficulty restarting. If the engine fails to start, the sensor has likely worn out. What are the symptoms of a bad crankshaft position sensor? Cost of Replacing a Bad or Failing Crankshaft Position Sensor. Common signs of a faulty crankshaft position sensor include issues starting the vehicle, intermittent stalling, and the Check Engine Light coming on. Our certified technicians can come...
Other

What does the OBD code p0491 mean?

What does the OBD code p0491 mean? P0491 code definition. This is the OBD-II code for Secondary Air Injection System Insufficient Flow Bank 1, indicating a problem on the side of the engine which contains cylinder #1. What to do if your vacuum leak is p0491? Solutions for P0491 may include: Repairing or replacing any damaged vacuum hoses or fittings which could be causing a vacuum leak Technicians note that this malfunction almost always occurs in times when the weather is cold. What is the code for check engine light? This can happen for multiple reasons and a mechanic needs...
Common questions

What kind of engine does a Jeep Wagoneer use?

What kind of engine does a Jeep Wagoneer use? This iron block 258 cubic inch I-6 cyl was introduced in 1971 and stayed in the jeep family until 1990. Gladiator/J-Series Trucks pickups and the Wagoneer were the first to use this engine. In 1972 the CJ's (including the CJ-5) were powered with this reliable mill. When did the Jeep Wagoneer Limited come out? The 1981 Jeep Wagoneer Limited is that ideal classic 4x4 that mixes big comfort with serious vintage appeal. So as these become more and more popular, its great to find an example that remains fini... More Info...
Easy tips

What year did the 24V Cummins come out?

What year did the 24V Cummins come out? 5.9L Cummins 24v SpecsProduction Years:1998 - 2007Injection:Direct Injection (DI)1998.5 - 2002Electronically controlled Bosch VP44 rotary injection pump2003 - 2007Bosch high pressure common rail injectionAspiration:Single turbocharger, air-to-air intercooler What year did the 5.9 Cummins come out? The common-rail 5.9L Cummins was produced from 2003-2007 and featured a fixed-geometry turbo. It put out 325hp and 610 lb-ft of torque by the end of its run, along with 359 ci of displacement coming from a bore of 4.02 in and stroke of 4.72 in. When did the 2nd generation Cummins diesel come out? Even as...
Other

When to replace serpentine belts in your car?

When to replace serpentine belts in your car? Serpentine belts are standard in just about any vehicle from the last quarter century. And they’re crucial for running everything from alternators to power steering. In other words, when it’s time to replace it, replace it. Serpentine belts will last you a few years, but depending on whom you ask,... How do you tighten up a serpentine belt? Another tensioner pulley uses a square-faced bolt for adjustment, and a third uses a large tab that can be set to a certain position for proper belt tightness. To remove an old serpentine belt,...
Easy lifehacks

Does a coil pack need to be grounded?

Does a coil pack need to be grounded? The simple answer is no, the coil case does not have to be grounded for the ignition to work properly. The coil does not need an electrical ground, but it does need a thermal ground for heat dissipation, meaning that the "ground" could be compromised by paint etc. Can a bad coil pack cause a Dodge Caravan to misfire? Spark Plug Wires – On most modern engines, the plug wires are not nearly as long as they once were, but they can still go bad. Here’s how to tell if your plug...
Common questions

What to do if your Dodge Ram has a transmission problem?

What to do if your Dodge Ram has a transmission problem? Ask your Dodge dealer. No one has added a helpful site for this 2006 Ram 2500 problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: After only 136,000 miles on the vehicle that is a 4x4 diesel it should not have needed a rebuilt transmission. What was the worst year for Dodge Ram transmission? The 2001 Dodge Ram 1500 was hands-down the worst model year for the Ram’s transmission. On CarComplaints.com, they list this model year as a clunker that you...
Common questions

Why does my car pull after applying the brakes?

Why does my car pull after applying the brakes? The only way to diagnose this problem is by examining how the car pulls once you apply the brakes. Usually, if there is a collapsed brake hose then the car will only pull for a few seconds after you apply the brake and then go back to normal afterward. What does it mean when your brakes don't work? Brakes have several means of telling drivers that they need some attention and TLC. That usually involves an unwelcome sound, or a strange or ‘weak’ feel at the brake pedal. There’s another popular...