Common questions

What causes steering wheel shimmy at 60-65mph other than tires?

What causes steering wheel shimmy at 60-65mph other than tires? Toyota 4Runner Questions - What will cause a steering wheel shimmy at 60-65mph other than tires, - CarGurus What will cause a steering wheel shimmy at 60-65mph other than tires, rims, balance, front end alignment? I have a 2016 4Runner SR5 Premium with 17000 miles on it. Since about up to 65mph. Then, goes away above that. Why does my steering wheel vibrate when I go over 50 mph? Be sure to have the rotor checked and skimmed or replaced completely if needed. A worn out or rusted brake caliper...
Most popular

How much does it cost to replace a cylinder 2 fuel injector?

How much does it cost to replace a cylinder 2 fuel injector? The technician pulls codes and diagnoses an open in the cylinder 2 fuel injector. Diagnosis – 1.0hr at $80/hr, $80 Remove and replace direct injector – 1.1hrs at $80/hr, $88 Fuel injector – approx. $85 How does the fuel injector work on a car? The fuel injector is supplied with fuel pressure from the rail and the ECM (electronic control module) controls the electrical signal to the injector; opening it for a specific amount of time and injecting the proper amount of fuel into the cylinder. What are...
Other

What happens to coolant when clutch fan fails?

What happens to coolant when clutch fan fails? When cooling fan operation fails it will cause engine coolant to retain heat, forcing the engine to run hot and eventually overheat. The first clutch fan was developed in the late 1960's and was in full production by the early 1970's. This clutch fan was designed to save energy and lower emissions. What does it mean when a fan clutch is making a noise? If a customer comes in with a fan clutch that’s making unusual noises, there’s an issue that needs to be fixed as soon as possible. If you’re not...
Most popular

Where are the cylinders located on a Ford Escape?

Where are the cylinders located on a Ford Escape? Because of the construction of these engines, the cylinders are all located at a 60 degree angle from one another, regardless of the year in which the engine was produced. Verify the generation of your engine. Locate the casting number on the engine block. Is the Ford Escape a 4 cylinder car? The Escape may be missing a cylinder, but its 1.5-litre displacement matches its four-cylinder turbocharged rivals, and likewise its power (181 hp) and torque (190 lb.-ft.) are comparable both with other turbo 1.5s and with other competitors’ larger-displacement non-turbo...
Most popular

How does the oil travel from the Pan to the overhead cam?

How does the oil travel from the Pan to the overhead cam? Oil travel from the pan to the overhead cam and heads on the 5. The oil also flows over the followers (rocker arms) when it flows out from the camshaft journals and the tappets then drains back to the oil pan. Oil also flows through the cylinder heads to the VCT solenoids through oil passages in the head. How are solid lifters used on hydraulic cams? Solid lifters on a hydraulic cam? This new trend in cam design is actually drifting over to cams made for hydraulic lifters,...
Easy lifehacks

What is a Ford EVAP system?

What is a Ford EVAP system? The evaporative emission control (EVAP) system in your Ford prevents fuel vapors from escaping into the atmosphere. The fuel vapors from the fuel tank are absorbed and stored by charcoal pellets in the charcoal canister. Where is the EVAP canister located on a Ford Explorer? Evap Canister Location: Where Is Evap Canister Location on Ford Where is evap canister location on ford 2002 explorer? have the same problem? The EVAP canister is located at the rear of the car near the fuel tank here are diagrams below to help you change it out. What...
Easy tips

What causes a car to go into limp mode?

What causes a car to go into limp mode? A bad MAF sensor or clogged catalytic converter can also cause an engine misfire. Driving a vehicle where one or more of the cylinders are not firing causes damage to the catalytic converter and can cause the engine to overheat. Mass Air Flow Sensor A defective MAF sensor can trigger the LIMP MODE. What to do if your transmission is in limp mode? Make sure that you are somewhere safe. Make sure that the engine has been off for at least 5-10 minutes. This will give the engine computer a few...
Most popular

Why does my Ford F-150 make a loud idle noise?

Why does my Ford F-150 make a loud idle noise? My car has an automatic transmission. Noise and/or failure of the variable cam timing phasers is a well known issue on the 5.4L V-8. In 2006, Ford issued a technical service bulletin, denoted TSB 06-19-8, to explain the service and repair procedures to deal with the noise. Typically, worn phasers create a loud and rough idle. When to replace cam phaser on Ford F-150? While the problem may not be as widespread as some believe, phaser wear can show up around the 50,000 mile mark, and if left unchecked, can...
Easy tips

Is a Ford Focus AWD?

Is a Ford Focus AWD? The new Ford Focus RS uses a GKN all-wheel drive (AWD) system with a Twinster twin-clutch system. And in Ford's drift mode, the AWD system delivers even more torque to the rear axle, delivering enough torque to the rear wheels for the RS to achieve a controlled “drift” through corners. Which Ford Focus has all-wheel drive? Ford Focus S Sedan: A 2.0-liter four-cylinder engine, a five-speed manual transmission, and front-wheel drive are standard in the base S trim; a six-speed automatic transmission is available. The RS trim also comes with all-wheel drive, trim-specific drive modes,...
Most popular

What should ICP be at?

What should ICP be at? For the purpose of this article, normal adult ICP is defined as 5 to 15 mm Hg (7.5–20 cm H2O). ICP values of 20 to 30 mm Hg represent mild intracranial hypertension; however, when a temporal mass lesion is present, herniation can occur with ICP values less than 20 mm Hg [5]. What does it mean when your IPC says disconnect? IPC disconnect indicates that the camera is out of the range or not powered on. How to resolve IPC disconnect error Please check if the antenna is securely connected to the camera and vertically...