Easy lifehacks

How are MAF sensors different from IAT sensors?

How are MAF sensors different from IAT sensors? MAF is an acronym for "mass air flow." Unlike IAT sensors, MAF sensors measure air volume with temperature at once. Remember, the MAP sensor above measured intake manifold pressure / vacuum and then estimated air volume with computer software. An MAF actually measures real air volume so that the computer doesn't need to guess what it might be. Where is IAT sensor located on air cleaner? IAT SENSOR IS MOUNTED INSIDE INTAKE AIR HOSE TO THE AIR CLEANER ASSEMBLY. THE MASS AIR FLOW SENSOR IS ALSO MOUNTED TO THE INTAKE AIR HOSE...
Easy lifehacks

Where do you plug in a wire harness?

Where do you plug in a wire harness? Our custom wiring harnesses use two or more OEM connectors to plug in at the taillight assembly and provide a standard trailer socket to allow a trailer to be plugged into your vehicle’s power system. This harness provides a 4-way flat connector socket and comes with a circuit-protected converter. How to troubleshoot no power at the factory plug? Next, test the pins on the connector where the wiring harness plugs into the truck using a circuit tester like Item # 40376. This will tell you if the problem is on the wiring...
Easy tips

Why does my car shake only at 60 mph?

Why does my car shake only at 60 mph? Tires are the most common reason a car shakes when it reaches 60-mph. Tire balance, or lack thereof, makes the steering shake as the car increases in speed. Typically, the shaking begins as an automobile gets to 55 mph and only becomes more problematic as the speedometer increases to 60 or more. Why do I get vibration at 55 mph? Vibrations @55-60mph. Uneven tire wear causes this kind of problem. Try this, rotate the front tires and see if the vibration goes away or happens at a different speed. If not...
Most popular

Are C6 automatic transmissions good?

Are C6 automatic transmissions good? The 6 speed automatic is actually a pretty good transmission, but if you want a manual - then get a manual. If you settle for the auto you'll end up hating the car. Also - I too would consider waiting a year to buy a C6. Are there any changes to the corvette in 2007? 2007 Did not bring any major changes to Corvette, the coupe, convertible and Z06 models were available with no change in horsepower or transmission options. The manual was offered in all three models and the six speed transmission was offered...
Easy tips

Why does my engine rattle when I Turn on the engine?

Why does my engine rattle when I Turn on the engine? What’s actually happening is measured in thousandths of an inch. The microscopic layer of oil between the crankshaft and the connecting rod bearings has worn wider than its normal half-a-hair width. The connecting rod slams against the crankshaft every time the piston moves up or down. The impact makes the wear worse too, coincidentally. What happens when you have rod knock on your engine? When you have rod knock, you’ll need an engine rebuild or replacement. It’s a sign of oil starvation, which means a simple rod bearing replacement...
Most popular

Is there a recall on GM windshield wipers?

Is there a recall on GM windshield wipers? November 6, 2018 — A General Motors windshield wiper recall is under federal investigation after complaints poured in from GMC Terrain and Chevy Equinox drivers about wipers that stopped working. When do windshield wipers stop working but can hear motor? It's an alarming experience when your wipers stop working in a heavy downpour, especially at highway speeds. You don't miss wipers until they don't work. Windshield wipers not working but can hear motor? When your wipers stop working, and you can hear the wiper motor running. The problem is most likely a...
Common questions

Should pitman arms be straight?

Should pitman arms be straight? There should be a maximum change in sine and a minimum change in cosine therefore, the pitman arm should be perpendicular to the axle with the wheels straight. The draglink adjusts to make put the steering wheel in the proper position with the wheels straight. How do you replace the idler arm on a pitman? Place the idler arm's bolt in the centerlink. Insert the new bolts through the frame making sure to put the new washers under the bolt heads. Position the idler arm so the frame bolts slide through the bolt holes. Install...
Other

How can I fit a pioneer audio system in my car?

How can I fit a pioneer audio system in my car? Configure a Pioneer audio sound system that fits your vehicle. Just plug in your vehicle information below and the Pioneer FitGuide will show you a listing of car audio products that should fit your specific vehicle. Is the pioneer D Series car stereo compatible with Android? Our new AVIC-W8400NEX and AVH-W4400NEX are compatible with Android Auto Wireless and Android Auto via USB when used with a compatible Android smartphone. . The D series is a result of Pioneer's automotive loudspeaker engineering experience and expertise, combining advanced design techniques with...
Easy tips

How do you turn on high idle 2021 Duramax?

How do you turn on high idle 2021 Duramax? To activate the high idle, turn your switch into the ON position and switch the cruise to the ON position. This should result in an idle of 800RPM. Press the SET button on Page 3 the cruise and the RPM should climb to 1200. Slide the switch to RESUME and the RPM should be at 1800. Where is the fast idle switch on a Duramax? The manual fast idle switch is operated using the cruise control buttons on the left side of the steering wheel. . The parking brake is set....
Easy lifehacks

What is axle shaft assembly?

What is axle shaft assembly? An axle shaft assembly may also be referred to as “CV Axle” or “Half-Shaft.” The axle shaft assembly (axle shaft for short) is a narrow rod like part with joints on either end that is used to transfer rotating power from your car transmission to the wheels. How much does axle work cost? The repairs can cost you anywhere from $170 to $900 or more. It depends primarily on the kind of car you have, as the parts will range in price quite a bit. Labor costs are typically between $100 and $200, but a...