Most popular

What to do if your Mercedes 450SL dies?

What to do if your Mercedes 450SL dies? Replaced points with Petronic 1885, along with replacing coil and wired per thread on this forum. Engine cranks fine cold and runs until it reaches operating temperature and idles down. Length of idling before engine dies varies each time. What's the problem with my 1974 450SL? It ribs up fine when cold, no issues. It seems the AAV and the cold start valves are working good, and it idles down after it closes, then after the temp bulb reaches operating temp, the computer changes to normal operation, and relies on throttle position,...
Easy lifehacks

When does the ignition warning light come on?

When does the ignition warning light come on? While it was written particularlly for the Morgans, the general theory is valid for most cars. (ED: The ignition light is used to tell when a generator (or alternator) is charging the battery. When the light is on, it means that you are running off the battery or discharging the battery. Why do I have a problem with my ignition light? There are several possible causes. On a dynamo it may be damaged brushes , a worn commutator or possibly faulty internal windings. With an alternator the problem may be caused by...
Other

How to replace front wheel bearings with MG Midget?

How to replace front wheel bearings with MG Midget? Comprehensive article about MG Midget & Austin-Healey Sprite front wheel bearing replacement, shimming, comparison to MGB bearings and technical drawings. Why are my kingpins worn out on my MGB? If you look straight at the front wheels from in front of the car, the wheels should appear to be straight up & down. If the tops of the tires are closer together than the bottom, the kingpins are probably worn out. Excess tire squealing while cornering at moderate speed. How to replace the brake disc on a MGB Kingpin? Remove the...
Easy lifehacks

How do you remove timing chain from Corvette?

How do you remove timing chain from Corvette? The cover will most likely be stuck to the block by old gasket material and sludge. Gently pry the sides of the cover with a screwdriver or similar instrument. Using a crankshaft socket and a breaker bar, spin the motor in proper rotation to align the timing marks on the two sprockets. What's the best way to align timing marks on a motor? Gently pry the sides of the cover with a screwdriver or similar instrument. Using a crankshaft socket and a breaker bar, spin the motor in proper rotation to align...
Easy tips

When did the Chevy 283 small block come out?

When did the Chevy 283 small block come out? In 1957, GM used the 283 small-block in three models: the 150, 210 and Bel Air. GM expanded the use of the Chevy 283 in the years after to include the Delray, Biscayne and all their station wagons. All Chevy 283 ignition system times are measured in degrees before top dead center (BTDC). What causes a Chevy 283 to lose power? This provided greater durability for the timing chain and related crank and cam sprockets. A common problem with the 283 was that the rocker arm stud would back out of...
Common questions

What is the wiring diagram for a Ford F250?

What is the wiring diagram for a Ford F250? 1967 Ford Ignition Switch Wiring Diagram Blog Diagrams Reactor 1970 Ford F100 Distributer And Coil Wiring Diagram Answer Ford 4 0 Spark Plug Wiring Diagram Diagrams Rest Split Diagram 1999 Ford F250 Ignition Switch Wiring Full Version Hd Quality Waldiagramacao Bellobuonoevicino It Distributor Ignition Coil Wiring Diagram Diagrams Show Computing What kind of wiring diagram does a 1970 Ford F100 have? 1970 Ford F100 Distributer And Coil Wiring Diagram Answer Ford 4 0 Spark Plug Wiring Diagram Diagrams Rest Split Diagram 1999 Ford F250 Ignition Switch Wiring Full Version Hd Quality...
Most popular

What to do when your fuel gauge reads empty?

What to do when your fuel gauge reads empty? If the gauge now reads empty, the sender is not grounded or the sender is bad. • Ground a test lead and touch it to the sending unit terminal on the back of the dash gauge (it is often marked with a red paper tag). If the gauge now reads empty, the wire between the sender and gauge is broken, or there is a poor connection at the gauge. Why is the fuel gauge on my Chevy truck not working? The most common problem with the fuel gauge reported by Chevy...
Other

What is an internal control module?

What is an internal control module? OBD-II Code P0601 is defined as a Internal Control Module Memory Check Sum Error. The PCM or Power Train Control Module performs many vital functions in a modern vehicle, such as management of the Fuel System, Ignition System, Transmission, Anti-Lock Brake and Traction Control systems. How do I fix my po603? How to Fix P0603Fully charge your battery so all measurements you take are accurate.Inspect the battery cables for corrosion, damage or loose connections.Make sure the wires going into the fuse box wiring harness are undamaged.Located and inspect the engine control module and all...
Common questions

Is the AWD tire replacement myth or truth?

Is the AWD tire replacement myth or truth? The AWD Tire Replacement Myth, Or Truth? So, it seems that the AWD tire replacement myth is not a myth at all. The vehicles do not all of their tires to be replaced at the same time. Some people may think of keeping the tires that still have some tread life on them because changing all the four tires is expensive. Do you need all four tires for AWD? But, an AWD vehicle needs balanced traction at all four corners. Mismatched tires on AWD may lead to the damage of several components....
Easy lifehacks

Why does the fan keep running on my TDI se?

Why does the fan keep running on my TDI se? My 2013 TDI SE has 5500 miles. In the past few days the engine fan continues to run after only short trips (3 miles). The only way to shut it off is to start the engine and then turn it off. This happens after Why does the engine fan keep running after engine is stopped? In the past few days the engine fan continues to run after only short trips (3 miles). The only way to shut it off is to start the engine and then turn it off. This...