Most popular

What are the different lights in a car?

What are the different lights in a car? Car lights include:Headlights. There are two types of headlights—low beam and high beam. Tail lights. Daytime running lights. Fog lights. Signal lights. Brake lights. Hazard lights. Driving lamps. When do you turn on your driving lights? Most cars have daytime driving lights that automatically turn on when the car is running to provide additional visibility to other cars. Usually, there is an option to turn these off if you don’t want them on. If available, it is useful to set your lights on automatic so your car can adjust to the amount...
Common questions

Is the 2003 Dodge Grand Caravan been tested?

Is the 2003 Dodge Grand Caravan been tested? The 2003 Dodge Grand Caravan has not been tested. Like what you see? Find the best deal on a Dodge Grand Caravan today. There are for sale near you. Certified child passenger safety technicians conduct hands-on tests of a car’s Latch system and check the vehicle’s ability to accommodate different types of car seats. Is the Dodge Caravan the same as the 1996? The 2001 redesign might not amount to as much of a forward leap as the 1996 restyling did, and competition has stiffened considerably since then. Even so, Dodge is...
Other

Why is my driver side airconditioner not working?

Why is my driver side airconditioner not working? There is only one a/c and only one temperature of air comming from the a/c coils. What could be happening, and I think this would be rather rare, is that the "doors" in the system that direct air flow are not operating properly on the driver side. ie. they are in the fresh are or ambient air mode. Why does my car AC blow cold air on one side? If the car AC blows cold air on one side and hot on the other, there are a few different causes but it's...
Other

How do you remove the ignition switch on a Sebring?

How do you remove the ignition switch on a Sebring? If your Sebring is equipped with a loop antenna, remove this from the ignition switch as well. Remove the three ignition switch mounting screws with the tamper proof torx bit. Set these screws aside. Pull the ignition switch from the steering column until the column lock actuator is exposed. How do you remove a key from an ignition switch? Insert the key into the old key lock and turn it to the start position. You will see the lock pin emerge from the lock cylinder. Push the lock pin in...
Most popular

How important is a crankshaft sensor?

How important is a crankshaft sensor? One of the most important parts of your vehicle is the engine and its parts like the crankshaft position sensor that keep your engine working properly. The crankshaft position sensor has the important job of monitoring the engine's many moving parts including the crankshaft, engines valves, and pistons. Can a crankshaft position sensor be replaced at home? If you are experiencing any of the symptoms above, have a mechanic take a look at your car. They make is simple to have your crankshaft position sensor replaced because their mobile mechanics will come to your...
Most popular

What kind of gas does a Chrysler 300c take?

What kind of gas does a Chrysler 300c take? The kind of gas the Chrysler 300c takes is regular gasoline. Having the fuel burn efficiently is the key to maximizing Your miles per gallon. How many miles per gallon does a Chrysler 300C get? The USEPA -rated fuel consumption of the 300C is: 15 miles per US gallon (16 L/100 km; 18 mpg ‑imp) city, and 23 miles per US gallon (10 L/100 km; 28 mpg ‑imp) highway. When all eight cylinders are needed, the 300C can produce 340 hp (254 kW) and 390 lb⋅ft (529 N⋅m) of torque. How...
Easy lifehacks

How to replace front wheel hub and bearing?

How to replace front wheel hub and bearing? Raise the vehicle on a suitable hoist. Refer to the detailed service procedures available in DealerCONNECT > TechCONNECT under: Service Info > 04-Vehicle Quick Reference > Hoisting > Standard Procedure > Hoisting. 4. Remove and replace the front right and left wheel hub and bearing. What do you need to replace front axle bearing? You will need the proper size socket to remove the axle nut and a torque wrench of proper capacity to tighten it. What were the symptoms that made you think the bearing was bad? What kind of Hammer...
Easy lifehacks

Which is diagnostic trouble code for internal control module memory?

Which is diagnostic trouble code for internal control module memory? P0601 is a diagnostic trouble code (DTC) for "Internal Control Module Memory Check Sum Error". Is the 262 DTC code a SAE code? I've also got the equivalent SAE codes listed, which are the official generic ones, the ones that are displayed on the dash are an FMC code format as far as I can tell. This lot suggests the 262 DTC code is an SCP error - nothing to worry about, just a comms glitch. What does DTC stand for in Powertrain Control Module? Diagnostic trouble code (DTC) P0601...
Most popular

How do you remove a blower motor resistor?

How do you remove a blower motor resistor? Carefully lift the glove box out from under the dash and set it aside. Remove the screws that secure the blower motor resistor to the housing, and put them someplace safe. At this point, you can remove the resistor from the housing. Disengage the wire harness locking tab, and disconnect the wire harness from the blower motor resistor. Where is the blower motor located on a car? Detach the cover from the bottom of the lower dash—it’s usually held in place by screws or clips. Do It Right: Be careful around the...
Common questions

When to go to the Mechanic about a bad timing chain?

When to go to the Mechanic about a bad timing chain? If the belt is jumping because it’s gotten loose, it can also flail around and damage other parts of the engine. If your engine won’t start or starts driving rough, indicating it may be on its way to failing, contact a certified mechanic for inspection and repairs. 4. Check Engine Light is on Who is going to tear down a Ford engine? Ryan Peart of JGM Performance Engineering has been assigned to tear down and inspect this engine. JGM will build it stock, dyno test it, and knock it...