Easy lifehacks

How does the no start glow plug relay work?

How does the no start glow plug relay work? The system is actuated when the ignition switch is turned to the RUN position. The "WAIT TO START" indicator lights until the glow plugs reach the proper temperature. The indicator goes out and the engine can be started. The afterglow operation of the glow plugs continues after the "WAIT TO START" indicator turns off. What happens after the glow plugs turn off? The afterglow operation of the glow plugs continues after the "WAIT TO START" indicator turns off. The glow plugs cycle on and off for a period of time. How...
Other

How often should ignition wires be changed?

How often should ignition wires be changed? The ignition cables on a car are made to last about 60,000 miles before they have to be replaced. In some cases, the wires will need to be replaced due to the rubber boots on the end getting damaged and now allowing for a good connection with the spark plugs. Do you have to change the spark plug wire? If your vehicle came with MAG wires, you MUST replace them with the same type. The third type of spark plug wire is the fixed resistor style. They’re made with a steel or copper...
Common questions

Can a VVT solenoid cause a oil leak?

Can a VVT solenoid cause a oil leak? The seal over time starts to leak oil. The oil leak is on the valve covers where the solenoid pokes out of the valve cover. Replacing the VVT Solenoid Seal is a very easy job and should only require the use of a small flat blade screw driver and should only take about 10 minutes. How do you seal valve cover gasket? Although valve cover gaskets don't necessarily need sealers or cements, it's a common practice to glue the gasket to the valve cover. There are a number of sealant choices, too....
Common questions

How to turn off the anti theft system on a Ford Escape?

How to turn off the anti theft system on a Ford Escape? On a ford escape remove positive cable from battery, place key in car and turn to the on position, then replace positive cable, turn key off then back on to reset anti theft system. Worked on 2005 escape! Thank you so much! I followed the advice from Jay. C and this just worked for me. Why does my 2011 Ford Escape not start? 2011 Ford Escape limited this didn't work. Tried it mutiple times like what you said and still it won't start. Kind of in a pickle...
Most popular

What are the problems with a 2004 Ford F-150?

What are the problems with a 2004 Ford F-150? 1 Window Does Not Roll Up 2004 F-150 Average Cost to Fix: $300 Average Mileage: 67,000 mi 2 Engine Failure 2004 F-150 Average Cost to Fix: $5,800 Average Mileage: 104,000 mi 3 Engine Knocking 2004 F-150 Why is my Ford F150 making a noise? Drivers have complained about a chattering sound in the rear part of the Ford F150, specifically the 1990-96 models. The noise occurs during soft turns in the vehicle after driving at high speeds. The problem came in an insufficient friction modifier or a faulty Traction-Lok differential. Why...
Common questions

Is the Ford Escape under investigation for stalling?

Is the Ford Escape under investigation for stalling? The National Highway Traffic Safety Administration is investigating the 2013 Ford Escape SUV after reports of the vehicle stalling. The government agency received 40 complaints that the 2013 Ford Escape suddenly stalls while driving. According to the NHTSA ‘s website, the Escape has a history of 15 recalls and two investigations. Are there any recalls on the 2013 Ford Escape? The government agency received 40 complaints that the 2013 Ford Escape suddenly stalls while driving. According to the NHTSA ‘s website, the Escape has a history of 15 recalls and two investigations....
Common questions

How many miles can a 2018 F150 last?

How many miles can a 2018 F150 last? To begin with, perhaps the longevity of the F150 truck is a huge draw. On average, the Ford F-150 can last between 150,000 miles, to 300,000 miles– depending on maintenance and other factors. May experts that the Ford F-150 can last up to 300,000 miles, before there is an engine rebuild that is needed. What does the M mean on a Ford f150? The "M" or Manual shift lever position can be used to step the transmission up or down through 7 pre-programmed gears manually. Push the lever to the plus position...
Common questions

How to remove an ambient air temperature sensor?

How to remove an ambient air temperature sensor? Step 4: Remove the sensor. You should be able to then pull out, twist out, or unclip the sensor or unbolt it from its bracket. Once removed, inspect the sensor for any major damage. Ambient air temperature sensors are located in a relatively sensitive position in the front of the vehicle. How do you replace an ambient thermistor in an air conditioner? This DIY repair guide explains how to replace the ambient thermistor in a window air conditioner. The ambient thermistor is a sensor that detects the room air temperature so the...
Other

How do I start my f150 with a broken key fob?

How do I start my f150 with a broken key fob? You just have to place the original key inside this secret location. After placing the key in the small compartment at the bottom of the cup holder in the center console, continue to press the push start button. The vehicle will then start without any problems. What to do if your F150 remote won't start? F150 remote fob won't start truck? If playback doesn't begin shortly, try restarting your device. Videos you watch may be added to the TV's watch history and influence TV recommendations. Why is the FOB...
Easy tips

What causes the variable camshaft timing code p0012?

What causes the variable camshaft timing code p0012? This over-retarded timing condition could be during the advancing or retarding phase of the camshaft timing. What causes the P0012 code? The variable camshaft timing (VCT) oil control valve (OCV) stuck in the open position. What does the p0012 code on an ECM mean? The camshaft (s) is (are) adjusted by the ECM through the use of an oil control valve (s) (OCV) also called variable valve timing control solenoid valves. The P0012 code is set when the ECM detects the camshaft timing for the intake camshaft on bank 1 is more...