Other

What is a start enable relay?

What is a start enable relay? The Start Enable Relay is wired into the Transmission Electronic Control Unit (TECU) on the coil side of the relay. If the HCM uses the standard engine Starter, the 12-volt Cranking Relay is energized supplying battery power to the Start Enable Relay main feed, which then powers the Starter Solenoid. What to do if your Autoshift is not working? Some faults will not allow the AutoShift to shift into other gears. You can try to reset the system by powering the system down for 5 minutes which may clear the fault long enough to...
Most popular

Who are the members of the Detroit Fire Department?

Who are the members of the Detroit Fire Department? Quartered with Engine 10. Quartered with Engine 6 / Chief 3 / Haz-Mat 1. Quartered with Engine 18. Quartered with Engine 26. Current quarters of Medic 12. Quarters of Squad 6 / Medic 13. Quartered with Engine 51. Current quarters of Squad 5 / Medic 18. Quartered with Engine 21. Quartered with Engine 38. Quartered with Engine 47. What kind of engine is the Detroit engine? Every step of our design, testing and manufacturing process builds quality into every engine that bears the Detroit name. To build the DD5, we leveraged...
Easy tips

Will bad injector O-rings cause a no start?

Will bad injector O-rings cause a no start? A bad injector o ring can cause the vehicle to experience difficulty starting, misfires, a loss in power, acceleration, and fuel efficiency, and in more severe cases even stalling. Usually engine performance issues will come after a fuel smell or leak. Why do you need O rings on fuel injector? Fuel systems are always maintained under pressure whether the engine is running or not. The O-rings on injectors are designed to seal all fuel and fuel vapors from escaping into the engine compartment. Can a thin O-ring cause a fuel leak? Aftermarket...
Easy lifehacks

What are the replacement parts for a trencher?

What are the replacement parts for a trencher? PedestrianTrechers 7+2,10+2,12+2,14+4, 20+4,25+4|pg117-128 Mid-Sized TF600,25+4XP, 30+4,DH4,DH5|pg129-142 LargeRider DH4,DH5,70+4,TF1000, RoadRunner,760|pg143-150 TheNextEvolutionofTrencherChain (“TheNET”) Ballantine,Inc.inconjunctionwithourParentCompany(USTsubaki),have developedTheNextEvolutionofTrencherChainDesign,referredtosimplyas “The NET”. What's the difference between a trencher and a case? By partnering the philosophies of an Evolving Manufacturing Technology,CustomerRequirementsandBallantine’sfieldexperienceorthe workingmansschoolofhardknockswehaveputaplaninplaceforproduct innovationaswellascontinuousimprovementsofalreadycelebratedchain designs. Where can I get a new Astec trencher? TollFreeCustomerService 800-328-2424 FAX 763-427-2277 BranchOffice 801S.Dupont,SuiteG Ontario,California91761 TheNextEvolutionofTrencherChain(“TheNET”)| pg 1 ChainCharts| pg 2 - 4 SoilSpecifications| pg 5 PedestrianTrenchers Maxi-Sneaker Chain Options | pg 10 - 12 Hard Parts | pg 13 - 14 TF300 ChainOptions|pg16-21 HardParts|pg22-28 RT60/RT130/160 What kind of engine does case 360 trencher have? The...
Common questions

How big is a New Holland 311 Baler?

How big is a New Holland 311 Baler? Used - New Holland 311 Small Square Baler, 14"x18"x52" bale size, NH 70 Thrower, manual bale tension, quarter turn bale chute, 27x9.50-15 tires, 27x5.50-15 pick up tires What kind of thrower does New Holland 311 have? With 70 hydraulic thrower, electric controls. New Holland 311 Baler with #75 thrower, excellent condition we ran this baler and it works fine greased and packed wheel bearings Baler serial # 660655 , Thrower serial # 756534 Always housed and housed here We ship anywhere We can finance Call or email us for a freight rate...
Most popular

Is a 3406e overhead cam?

Is a 3406e overhead cam? The cam is in the head. It is referred to as a cam in head because it has to come out the front of the head. It does not have caps on top so they do not call it an over head cam. How to adjust the overhead settings on a 3406E? Recheck each adjustment. Remove the top center bolt, and turn the flywheel by 360 degrees in the direction of the engine's rotation. This will position the No. 6 piston at the top center on the compression stroke. Install the top center bolt in...
Other

What is the gear ratio on an Allison?

What is the gear ratio on an Allison? 1.383 1.000 6.035 .Gear ratio does not include torque converter ratio power takeoff*' Converter driven (one) Location Size of opening Ratio Drive gear rating Engine driven (two) (optional) Location Size of opening Ratio Rating 1q g'qlock position (as viewed from rear) SAE 6-bolt 1.00 x turbine speed lntermittent-4oo lb ft (5,13 Nom) What kind of gearbox does an Allison AT545 have? The AT545 is an Allison 4-speed automatic gearbox. The automatic gearbox comprises a hydraulic torque con- verter, a number of planetary gears disc clutches that lock What is the model number...
Most popular

Why is my 7.3L diesel engine not starting?

Why is my 7.3L diesel engine not starting? If you don't get 12V there with the relay activated, then replace the relay. If you get 12V out of the relay, then your problem is further down the line at the starter (or the starter mounted solenoid). While you have the small wire pulled off, check for voltage there when you turn the key to start. You should get 12V. Are there any problems with the Ford 7.3 power stroke engine? It’s also important to note – the Ford 7.3L Power Stroke diesel engine earns high remarks for reliability. They are...
Easy lifehacks

How to prevent accidents with skid steer loaders?

How to prevent accidents with skid steer loaders? To prevent accidents with skid steer loaders, read and follow directions in the equipment operator’s manual. Pay attention to safety instructions in the manual and to warning labels you see on the equipment. If you have questions, stop and ask your supervisor before you continue. Concentrate on working safely. How did a skid steer get its name? The skid steer gets its name from the way it turns. The angle of the wheels or tracks is fixed, so they will only point straight ahead. The wheels or tracks on each side of...
Most popular

How does spiralock threading work on a screw?

How does spiralock threading work on a screw? Spiralock threading puts a shoulder which is ground to a slightly different angle on the entire screw thread so the entire bolt or screw gets compressive loading along its shaft, locking it in place by friction when the screw is tightened, while still permitting easy turning until it is tightened. Why are threaded components used instead of bolts? These may be used instead of bolts for precision, ease of assembly, and reduced component play—likely a combination of factors in excess of what we've already mentioned. - Threaded Components - these are most...