Common questions

Why does my truck tick when I accelerate?

Why does my truck tick when I accelerate? A ticking sound could be caused by any number of reasons, such as a low level of oil or loose components. You may hear a ticking, clicking, or tapping noise while the vehicle is idling, accelerating, or even after receiving an oil change. Why does my Chevy Silverado run at high RPMs? If it is a 4X4 maybe it is low range. 2 people found this helpful. 3 people found this helpful. With those RPM's it won't last long. Does it sound like it is revving that high or is the tach...
Easy lifehacks

Where are the fuses on a Chevrolet TrailBlazer?

Where are the fuses on a Chevrolet TrailBlazer? Removed the fuses (#36 and #39)and then re-inserted them after waiting about a minute. After re-insertion, turned ignition but did NOT start the engine. Heard the calibration take place behind the A/C controller for about a minute. Why are the vents not working on my Chevy Trailblazer? When I reconnected the battery the AC controller recalibrated itself and everything worked fine. Later I replaced the car's (05 Trailblazer) battery and the top vents quit working. According to the schematics I had, this was due to the mode control door not working right....
Easy lifehacks

What to do if you have a slipping transmission?

What to do if you have a slipping transmission? To fix this, you will have to get the clutch plates replaced immediately and also change the fluid. Low fluid levels are often involved with any problem that involves slipping transmission. What causes the gears to slip in an automatic transmission? Bands are what link the gears in the automatic transmission together. To fix this problem you need to replace or adjust the defective band. Transmission slipping can also be affected by worn out gears, solenoid problems, or torque converter issues. Why does my transmission band Keep Slipping off? Worn or...
Easy lifehacks

How to set the timing on a 350 Vortec?

How to set the timing on a 350 Vortec? Start the engine and bring to normal operating temperature. Increase engine speed to 1000 RPM. Monitor the Cam Retard Offset. If the Cam Retard indicates a value of 0° ± 2°, the distributor is properly adjusted. If the Cam Retard does not indicate 0° ± 2°, the distributor must be adjusted. What should timing advance be on a 5.7L 350 Merc? You have vortec heads on your new engine. They need 4 degrees less advance than the old style heads. 28 degrees is max recommended advance on vortecs, and 32 degrees...
Easy lifehacks

What are the specs for a Corvette LT1?

What are the specs for a Corvette LT1? LT1 Corvettes (Y-bodies) of this model year used camshafts with 205/207 degrees of intake/exhaust duration at 0.050-inch lift. Total advertised duration is typically about 70 degrees higher, but airflow below 0.050-inch valve lift is almost nonexistent. What kind of SERV did a 1994 Corvette use? Corvette 1994/1995 may have used Serv. No. 16181333. All 94+ LT1 PCM's are aluminum in color with 4 rectangle plugs. 94-95 PCM's can be flashed through the diagnostic port using rather inexpensive hardware and software. When was the last year a corvette had a tach? 1958 was...
Most popular

What do you need to know about the EGR valve?

What do you need to know about the EGR valve? The EGR valve is a small component designed to allow the flow of exhaust gases into the intake manifold in controlled amounts. As such, it's a simple valve that closes and opens as needed. Where are the EGR Jets in the intake manifold? A more radical design, implemented in a few models, was the replacement of the valve with EGR jets at the bottom of the intake manifold. Some newer high-efficiency engines, for example those with variable valve timing (VVT), don't even use an EGR system. If playback doesn't begin...
Common questions

What are the symptoms of a failing 4L60E transmission?

What are the symptoms of a failing 4L60E transmission? Though the shell is supposed to be one piece, not only can it break off, but it can also strip out the splines. Hard Second Gear – The third most common symptom of a failing 4L60E transmission is the difficulty in shifting to the second gear. The second is so hard that it almost feels like a shift kit has been installed. What does electronic shifting control on GM 4L60E mean? This means that a series of valve pressures made the transmission shift gears. GM made the jump to electronic shifting...
Most popular

Can a 2000 350 idle but not rev up?

Can a 2000 350 idle but not rev up? Idles just fine but wont rev up. I have a 2000 350 and it starts fine and idles ok, but ti will not rev up. When you give it throttle it sputters and will nor rev up.HELP. thanks:no::no: Why is my C / K 1500 surging at idle? TPS SENSOR BREAK INSIDE THESE THINGS AND CAUSE IRRATIC IDLE. THE IDLE AIR CONTROL IS ALSO NEXT TO IT PULL THAT AND ENSURE IT ISNT COVERED IN CARBON.IF IT IS CLEAN WITH CARB CLEANER What kind of help truck has HIGH idle? SilveradoSierra.com...
Easy tips

How do you break in a new Duramax engine?

How do you break in a new Duramax engine? Here's how to break in the engine in your new diesel pickup.Start By Running Your Engine Lightly for a Few Hours. Avoid Idling Your Diesel Truck. Continue to Gently Ramp Up Your Engine Use. Don't Tow for at Least 500 Miles. Begin Driving Hard After 15 Hours (or 1,000 Miles) How big is the DEF tank on a 2021 Duramax? The DEF tank is approximately 5 gallons (18.9 liters). On pickup trucks, the DEF tank fill nozzle is located on the passenger side, under the hood and is sealed by a...
Other

How do you bleed the brakes on a 2000 Chevy s10?

How do you bleed the brakes on a 2000 Chevy s10? have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on ... Can You Bleed the brakes on a GM car? Bleeding the brake system after changing the brakes can be hard on some anti-lock...