Easy lifehacks

Do you have to remove calipers to change brake pads?

Do you have to remove calipers to change brake pads? In most cases you’ll need to remove the calipers to change the brake pads. For fixed calipers, remove the caliper mounting bolts only if the pads won’t come out the back of the caliper. For floating calipers, remove the two caliper mounting bolts or guide pins. How are brake pads attached to floating calipers? For fixed calipers, remove any pins or retainers (push pads back and pull them out). For floating or sliding calipers, separate the pads from the caliper. The inner pad must be clipped to the piston. The...
Easy lifehacks

Do you grease an axle seal?

Do you grease an axle seal? To begin the seal installation, an important step is to pre-lubricate the seal with the oil or grease you are going to seal. This will reduce the “sliding“ friction force that can damage the seal when installed dry. It also prevents a dry starting condition that can tear the seal material during initial run-in periods. How to install a front inner axle seal? 1. Disassemble the front axle according to the steps listed in the factory service manual and remove the old inner axles seals using a long screwdriver and hammer to knock them...
Most popular

Why are my intake camshaft bolts broken on my BMW?

Why are my intake camshaft bolts broken on my BMW? This is a design defect, and well know in professional BMW service circles. You can see on the photo below, that VANOS (variable valve timing system) to intake camshaft bolts have broken and backed out, 3 of the 4 bolts are damaged and loose. What causes a camshaft to be broken in an OHC engine? If the cam timing is lost during high revs (broken chain or gears) the con rods will contact the camshaft causing the cam to be broken. Other serious damage can occur at the same time...
Other

What are symptoms of bad lower ball joint?

What are symptoms of bad lower ball joint? Top 4 Bad Lower Ball Joint Symptoms Vibrations. When you have a bad lower ball joint, you will be able to feel vibrations in the steering wheel or from the left or right side of the Clunking Sounds. A symptom of a faulty lower ball joint that people experience on a regular basis is clunking sounds. Tire Wear. Wandering Steering Wheel. ... How much does it cost to replace a ball joint? If you want the basic parts for a do-it-yourself ball joint replacement, it may cost around $35 to $75 per...
Easy lifehacks

What does stop vehicle, shift to P, leave engine running mean?

What does stop vehicle, shift to P, leave engine running mean? I got the message "stop vehicle, shift to P, leave engine running" with a Battery symbols and an Exclamation marks on my 2105 C300. Then I stopped, turn the car off, wait a 5 to 10 min and it ran fine on my 20 mile to work. Is it against the law to leave your engine running on a public road? The Highway Code states: ‘You MUST NOT leave a parked vehicle unattended with the engine running or leave a vehicle engine running unnecessarily while that vehicle is stationary...
Common questions

Does the manufacturer pay for recalls?

Does the manufacturer pay for recalls? A recall is issued when a manufacturer or NHTSA determines that a vehicle, equipment, car seat, or tire creates an unreasonable safety risk or fails to meet minimum safety standards. If there is a safety recall, your manufacturer will fix the problem free of charge. Are there any safety recalls on Ford cars? DEARBORN, Mich., Sept. 30, 2020 – Ford Motor Company is issuing one safety compliance recall and two safety recalls in North America. Affected vehicles have insufficient electrical conductivity within the printed circuit board internal to the camera. Is there a recall...
Common questions

What is the ANSI standard for emergency eyewash?

What is the ANSI standard for emergency eyewash? The ANSI/ISEA Z358.1-2014 standard provides instructions that units must be properly installed, positioned to deliver flushing fluid in the required pattern and at a safe, tepid temperature, accessible within 10 seconds of a potential exposure, and identified with appropriate signage. When did EC No 853 / 2004 come into effect? Regulation (EC) No 853/2004 introduces a new definition to cover products derived from eggs that, after removal of the shell, have not yet been processed. It is, therefore, necessary to clarify the rules applying to those products and amend Section X, Chapter...
Common questions

What size is the steering wheel on a Ford f150?

What size is the steering wheel on a Ford f150? The Ford F-150 steering wheel size is Outside Diameter: 15 3/4" and Grip Circumference: 3 7/8". The power steering fluid needs to be changed every 75,000 miles. Are all Ford steering wheels the same size? Did you know? Diameters of steering wheels typically range from 14 ½ inches to 17 ½ inches, and the grip circumference can range from 2 ¾ inches to 4 ¼ inches. What size steering wheel is on a 2006 f150? 15 3/4" Ford F-150 2006, Original One-Color Steering Wheel Cover by Wheelskins®. Outside Diameter: 15...
Other

Where do the brake calipers go on a car?

Where do the brake calipers go on a car? Well, brake Caliper Location usually depends on the make and application of a vehicle. Generally, you will find these assemblies at the wheels and on the front axle. The calipers typically attach to a car’s steering knuckles. Brake calipers mount on the steering knuckle in two different ways. It can be directly, supported by bolts and pins. Where are the Pistons on a floating caliper? Floating calipers are compact, lightweight, and not as powerful. They don’t mount rigidly and instead, slide freely on lubricated pins and bushings. Floating calipers come with...
Other

What kind of tool do I need to reprogram my Chrysler?

What kind of tool do I need to reprogram my Chrysler? For Chrysler applications, you need a Diagnostic and Reprogramming Tool (DART). Chrysler dealers use the Mopar Diagnostic System (MDS2) and DRB III scan tool. When was flash reprogramming made available to independent repair shops? Thanks to the passing of Senate Bill 1146 in September 2000, vehicles manufacturers must now make this technology available to independent repair shops at reasonable cost. Starting in 2004, flash reprogramming procedures must also conform to SAE J2534 standards which allow the use of aftermarket scan tools or similar pass-through devices. When did flash reprogramming...