Other

Why did my flywheel break?

Why did my flywheel break? Worn starter drive components, worn bushings in the starter, improper shimmed starters on vehicles that use shims, weak batteries and aged equipment cause flywheel problems. Most engines will stop in the same stop each time the engine is shutoff. Why is my starter not engaging the flywheel? Tighten the mounting bolts and other connecting wires. If the mounting bolt is loose, the starter drive will not engage the flywheel properly. It will make a grinding noise when you try to fire up your engine. What this means is that the pinion gear on the starter...
Easy tips

What should I do if my heater core is clogged?

What should I do if my heater core is clogged? In that case, you might have a clogged heater core. In that scenario, you can try flushing it out. Sometimes you can force compressed air and cleaner through a heater core to clear the blockage. I would suggest you try this first before attempting to replace a heater core. What happens when a heater core goes bad? A heater core often goes bad due to leaking. As the heater core uses engine coolant to generate heat, a leaking heater core will reduce the amount of coolant in the cooling system....
Easy tips

What to do if your engine cranks but fails to start?

What to do if your engine cranks but fails to start? If either the switch or the computer circuit fails; you may have a hard time starting the engine when cold. Also, for a engine cranks but fails to start problem, consider checking the exhaust system. Why is my car hard to start when it's cold? Poor fuel economy; low power, misfiring and, yes, hard starting engine when cold. Lack of necessary fuel system pressure will make it hard for your engine to start. This may happen on a cold engine; if pressure is slowly leaking or not building appropriately....
Common questions

How long does it take Ford to diagnose a car?

How long does it take Ford to diagnose a car? A standard diagnostic test can take about an hour to an hour and a half. Of course, more complicated issues that require further diagnosis and where components must be removed for access or testing can take 2-3 hours; depending on the severity of the issue or multiple underlying issues. What kind of system does the Ford Explorer have? 2021 Ford Explorer has available heated seats and heated steering wheel which are sure to keep you comfortable on your adventures. The Terrain Management System, available with both 2WD intelligent 4WD, can...
Easy tips

What does an EVAP purge valve do?

What does an EVAP purge valve do? The canister purge valve is a vital part of the Evaporative Emission Control System (EVAP). The EVAP system seals the fuel system of your vehicle to prevent harmful fuel vapors from entering the environment. What is the purge valve in a fuel tank? The canister purge valve, also commonly referred to as the purge valve, is an important component of your Evaporative Emission Control (EVAP) system. This system restricts the fuel vapours created in your fuel tank from escaping into the atmosphere by trapping them in a charcoal canister. What happens when a...
Common questions

How much will the All-Electric F-150 cost?

How much will the All-Electric F-150 cost? Ford's base model electric F-150 will cost $40,000 and can go 230 miles on one charge. - The New York Times. Business|Ford's base model electric F-150 will cost $40,000 and can go 230 miles on one charge. How long does it take to charge the new Ford f150 electric truck? Smart charging solutions made easyEstimated charge times 15% to 100% at 240 voltsStandard-range battery with targeted 230 milesExtended-range battery with targeted 300 miles80-amp Ford Charge Station Pro10 hours8 hours150-kilowatt DC Fast Charging (15% to 80%)44 minutes41 minutes What do you need to know...
Easy tips

Can an F-150 last 300000 miles?

Can an F-150 last 300000 miles? To begin with, perhaps the longevity of the F150 truck is a huge draw. On average, the Ford F-150 can last between 150,000 miles, to 300,000 miles– depending on maintenance and other factors. May experts that the Ford F-150 can last up to 300,000 miles, before there is an engine rebuild that is needed. How long does a Ford F-150 engine last? On average, the Ford F-150 will last from 150,000 to 300,000 miles before giving up the ghost. This is, of course, with regular care and maintenance. If the vehicle is used for...
Other

How do I know the towing capacity of my 5th-wheel?

How do I know the towing capacity of my 5th-wheel? Knowing this, it's simple math to calculate a general range of the largest fifth-wheel by multiplying your true cargo capacity by 4 for the low end (25% on the pin) and 5 for the high end (20% on the pin). With our example of 3255 lbs., we come up with 13,020 – 16,275. That is the maximum size of the fifth wheel. Is the Ford F-250 a fifth wheel trailer? Towing a Fifth Wheel Camper with a Ford F-250 - Travel, Rest, Repeat... Four years ago we decided to upgrade...
Easy lifehacks

When does the engine miss at 4000rpm?

When does the engine miss at 4000rpm? The engine misses/bucks (it is as if a gremlin is switching of the ignition) at just over 4000 when cool (block temp not water temp) as the block temp rises or load duration (climbing a grade) the miss/bucking will drop to around 3000rpm. Why does my boat not go over 3000 rpm? When pressure is leaking from the cylinder, the rpm is sure to reduce. Also, don’t forget to check the fuel pump pressure at the same time. This is a rule of thumb, always and I mean always, keep your boat clean,...
Easy tips

What kind of spare parts does hella have?

What kind of spare parts does hella have? Spare parts. HELLA offers you a great selection of spare parts. On the one hand, a great range of electronics for continuously rising repair volumes - with sensors, actuators and control units. On the other hand a broad range of electrical products that has grown over many years. How to create Hello World program in assembly language? Tutorial programs usually go by the name “Hello World” because that’s all they print out to the screen. Plenty of this information came from: http://www.tutorialspoint.com/assembly_programming/assembly_environment_setup.htm. Install the tools. Create a file called “~/hello.asm” and populate...