Common questions

When did PT Cruiser stopped production?

When did PT Cruiser stopped production? 2010 When did Chrysler stop making the PT Cruiser? 2010 was the last year for the Chrysler PT Cruiser. The last PT Cruiser came off the assembly line in Toluca, Mexico, on July 9, 2010. When was the last year the Chrysler PT Cruiser was made? For 2010, the last year of production for the PT Cruiser, there was only one trim level available: the PT Cruiser Classic. What was the name of the Plymouth PT Cruiser? The look was refined, and in 1998, another Plymouth concept called the Pronto Cruizer directly previewed the...
Easy tips

How much does a Chrysler Town and Country headlight cost?

How much does a Chrysler Town and Country headlight cost? The average cost for a Chrysler Town & Country General Diagnosis is between $88 -$111. Learn More Low beam driver side HID headlight won't work even with new bulb. Why does my driver side headlamp not work? Driver side headlamp does not work in low beam. High beams are fine. headlights flickered and did not illuminate while in the on position BOTH HEADLIGHTS QUIT WORKING. I HAD TO PULL OVER BECAUSE I COULDN'T SEE ANYTHING. I HAD TO WAIT TILL DAYLIGHT BEFORE I COULD DRIVE AGAIN. Why are my head...
Common questions

What to do if your convertible top is stuck?

What to do if your convertible top is stuck? This is as far as you can go without damaging the top parts. This will now allow you to get your arm in under the deck lid to unfasten the hinge pins or bolts on the deck hinges. Sometimes these pins or bolts bind due to the stress of the wedges and it becomes necessary to remove the hydraulic lines at the pump or deck cylinders. Why does my convertible top not open without a key? The trunk won't open without a key...unless the windows get stuck halfway up. Then the...
Easy lifehacks

How do I program my 2006 Jeep Wrangler key?

How do I program my 2006 Jeep Wrangler key? 2006 Jeep Wrangler Key ProgrammingInsert first programmed key into the ignition and turn ignition switch to ON. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Within 50 seconds insert the new unprogrammed key into ignition. How do you program a Jeep transponder key with one key? Turn the ignition switch to the ON/RUN position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing. To indicate that programming is complete,...
Easy lifehacks

How do I find my Uconnect PIN number?

How do I find my Uconnect PIN number? Uconnect AccessLog in to your Mopar.com account.Click Hello, [name] in the upper right corner.Select My Account from the drop down.Select Uconnect Access from the left side menu bar.Choose Update Your Uconnect Access Security PIN and follow the prompts. How do I find my Uconnect PIN? A PIN will be displayed on the screen. Alternatively, if your system has voice commands, you can say "Setup" followed by "Pair a phone". You will then be asked to confirm the four-digit PIN for your vehicles UConnect system. Refer to vehicle's user manual to obtain the...
Common questions

Where are audio amplifiers used?

Where are audio amplifiers used? Important applications include public address systems, theatrical and concert sound reinforcement systems, and domestic systems such as a stereo or home-theatre system. Instrument amplifiers including guitar amplifiers and electric keyboard amplifiers also use audio power amplifiers. Do all speakers have amplifiers? The vast majority of speakers are passive. A passive speaker doesn't have a built-in amplifier; it needs to be connected to your amplifier through normal speaker wire. Because the amplifier is an active electronic device, it needs power, and so you have to put any active speakers near a power outlet. What does an...
Other

Why do you have to press the clutch when starting?

Why do you have to press the clutch when starting? Pressing the clutch pedal while starting the car in neutral is vital to stay safe and sound. Numerous car companies provide various sensors in the clutch pedal. The car will start taking ignition only after pressing the clutch pedal in neutral. Why does my car say depress clutch pedal? Mine has developed an annoying fault whereby it sometimes won't start even with the clutch pressed fully down. Starter motor doesn't spin, and a message appears on the dash saying 'depress clutch pedal' or something like that. It will eventually start...
Other

What did I need to change my speedometer reading?

What did I need to change my speedometer reading? In the 90’s when electronic speedos first came out there was a menu in the speedo head where you could enter a code matching your tire size to correct readings. Is it possible to change the odometer on a car? Changing the odometer is the same as lying about the age of the car. In fact car manufacturers have gone to great lengths to make it difficult to do. Some put an ink bar in the assembly so that if tampering happens an ink smudge is put onto the number dials....
Most popular

Where is the power steering pump located on a Chrysler Town and Country?

Where is the power steering pump located on a Chrysler Town and Country? If driven by an electric pump, the pump may be mounted in conjunction with the steering shaft or in conjunction with the steering rack. With either a drive belt or electric pump, removal of any dash, panel, or steering components is performed to access the pump. The threaded connectors to the pump inlet and outlet are loosened and removed. How much does a power steering pump replacement cost? Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and...
Most popular

Does Town and Country have Stow and Go?

Does Town and Country have Stow and Go? The Town & Country comes standard with a power liftgate and Stow 'n Go second- and third-row seats that fold flat into the floor. Power folding third-row Stow 'n Go seats are optional. Can stow and go seats be removed? Fold the seats into the floor, remove the trim surrounding the openings. Clamp a visegrip onto the seats pivot shaft so when you remove it, it can't slide over to the side or you can get big ouch. remove the 3 nuts holding it in and pull it out. Click here to...