Common questions

Can I solder window defroster?

Can I solder window defroster? Even though the electrical tabs are soldered onto the defogger grid at the factory, avoid the temptation to solder the replacements. If the heat cracks the glass, you will have to buy a new window. What to do if rear window defogger is not working? If there on one side, you have just proved the switch, relay, fuse and wiring to the window is good. If there on both sides you are missing the ground to window. If voltage is there on one side, turn off and carefully disconnect wires at window. Why does my...
Easy tips

Why does my Ford F150 have insufficient flow?

Why does my Ford F150 have insufficient flow? That’s because the EGR valve is not always going to be the culprit. Here are some of the most common fixes to help clear the P0401: Check the EGR Tube- It’s a good idea to check the tube going to the EGR because it’s often the cause of P0401, easy to do, fast, and replacing it is very affordable. If it’s cracked, you’ll need to get a new one. What is the EGR code on a Ford F150? There are three main parts of the F150’s EGR system. They are the EGR...
Easy tips

Are Mustangs fuel injected?

Are Mustangs fuel injected? Your Mustang, as well as most fuel injected cars, has a one-to-one ratio fuel regulator. At idle, the engine is in a manifold vacuum situation and the fuel pressure is around -9psi to manifold pressure ratio. When did Mustang go Fuel Injected? 1986 When Ford introduced the 1986 Mustang GT with its fuel-injected 5.0 HO V-8, it marked a watershed moment in American performance. Is the Mustang EcoBoost direct injection? The 2.3L EcoBoost® engine in Mustang delivers 310 horsepower and 350 lb. -ft. of torque* with turbocharging, direct injection and twin independent variable cam timing (Ti-VCT)....
Other

What kind of pressure hose do I need for F-150?

What kind of pressure hose do I need for F-150? Stop exerting extra strength on a leaky hose and replace the damage today using a high-performance pressure hose for Ford F-150. The aftermarket Ford F150 power steering hose from AutoZone is custom-designed for your truck's high-pressure system. How do you replace power steering hose in Ford F150? Fill the power steering reservoir back with fluid, then start your car and turn the steering wheel from lock to lock a dozen or so times. Check the fluid's level, then top it off. Turning the steering wheel should push the air bubbles...
Other

When did the Ford Fusion brake system come out?

When did the Ford Fusion brake system come out? Introduced in the 2006 model year, the Ford Fusion rapidly became one of Ford’s top-selling cars. With styling cues taken from many European sedans, the Fusion brings with it design elements never before seen in a Ford car. The Fusion also borrows heavily on European design and technology in the brake system. How to check the brake pads on a Ford Fusion? Inspect the brake pads and shims for wear or contamination. There should be at least 3 mm of material and the pads should not differ from side-to-side by more...
Common questions

What is a mass air flow sensor made of?

What is a mass air flow sensor made of? The primary components of the MAF sensor are a thermistor, a platinum hot wire, and an electronic control circuit. The thermistor measures the temperature of the incoming air. The hot wire is maintained at a constant temperature in relation to the thermistor by the electronic control circuit. How are MAF sensors different from IAT sensors? MAF is an acronym for "mass air flow." Unlike IAT sensors, MAF sensors measure air volume with temperature at once. Remember, the MAP sensor above measured intake manifold pressure / vacuum and then estimated air volume...
Easy tips

What is the purpose of the heater control valve?

What is the purpose of the heater control valve? The heater control valve (sometimes called the hot water valve) is used to control the rate at which coolant flows through the heater core. The valve is located on the heater inlet hose. Manually operated systems may use a cable, a vacuum motor or an electric solenoid to operate the valve. How to check the temperature of a heater control valve? Then check the temperature of the hose on the inlet and outlet sides of the heater control valve. The inlet and outlet hoses should be the same temperature. If the...
Most popular

Where to find the camshaft position sensor on a car?

Where to find the camshaft position sensor on a car? You may have trouble spotting the sensor when you look under the hood of your car. Usually, different car manufacturers will have their own unique spot near the engine for mounting the sensor. How much does a bad camshaft sensor cost? In this case, because of an inaccurate reading from a bad camshaft position sensor, more fuel than necessary is injected into the engine which causes your fuel economy to drop. To replace a camshaft position sensor, you can expect to pay anywhere from $120 to $300. Parts alone will...
Easy lifehacks

What will a 6.9 Idi run on?

What will a 6.9 Idi run on? The 6.9L ('83 to '87) and 7.3L ('88 to '92) engines International (Navistar) built can be considered true old-school diesels. Many are drawn to this engine because it's able to run 100 percent biodiesel. What kind of engine does a 1986 Ford F 250 have? Today’s modern trucks are hugely capable, but that means little without a bit of perspective. This 1986 Ford F-250 Diesel was among the first generation to use the IDI engine, a predecessor to the modern Power Stroke V8. [Photo: TFLtruck] When did the Ford 6.9 diesel engine come...
Most popular

How much does it cost to replace a BMW water pump?

How much does it cost to replace a BMW water pump? Water Pump Replacement Estimate for BMW X5 BMW X5 Water Pump Replacement costs $663 on average. How much does a new water pump cost? Water Pump Costs Submitted By Our Users Repair Type Zip Car Year Car Make Cost Water Pump 91637 2009 smart $369 Water Pump 85047 2010 subaru $805 Water Pump 5038 2014 chevrolet $638 Water Pump 78822 2004 bmw $622 When is it time to replace your water pump? If you see significant leakage from that weep hole, it is time to replace the pump. Bearing...