Easy lifehacks

What are the parts in a GM tilt steering column?

What are the parts in a GM tilt steering column? Here are all of the parts in a GM tilt column, excluding the steering wheel: Inside the GM Tilt Steering Column Page 4 We start assembly with the core part, the column jacket assembly: This is the lower bearing with dust shield and ( 2 ) 8-32 x 1" self-tapping deformed-thread screws: Inside the GM Tilt Steering Column Page 5 What's the difference between automatic and manual steering columns? The column shown is for a manual transmission equipped Fiero as indicated by the key release lever. Automatic columns use a...
Easy tips

Why is the transmission in 3rd gear and not shifting?

Why is the transmission in 3rd gear and not shifting? Hi there. The transmission could have an issue with the shift solenoids. Check the wiring harness to the transmission case and make sure that it is plugged in. 3rd gear is the only forward gear in a 4L60E transmission that does not require electrical power. It is common for the electrical harness in the transmission to short out. Which is the only forward gear in a 4L60E? 3rd gear is the only forward gear in a 4L60E transmission that does not require electrical power. It is common for the electrical...
Most popular

How does the ignition work on a S-10 Blazer?

How does the ignition work on a S-10 Blazer? Troubleshooting the ignition system in your S-10 Blazer begins with a basic understanding of how the system works. Electrical power is supplied to the primary coil of your ignition coil by the ignition module, generating a magnetic field around the secondary coil in the ignition coil. Can a bad ignition switch keep a S10 from starting? A bad ignition switch can cause your S10 not to start at all. And, it can keep your S10 from starting in a couple of different ways. The first is when the starter cranks, but...
Common questions

Why is the temperature gauge on my Chevy truck not working?

Why is the temperature gauge on my Chevy truck not working? All I have the same issue, I own a 1996 chevy pickup c1500, before I replaced the temperature gauge sensor, the gage read two lines below 210, after I replace the temp gradually climbs but the engine not as hot as where the gage reads, need advice stephan is on point for the diagnostic procedure. First.it's not a thermostat issue. How to check a temperature gauge and sending unit? Here I check to see if the stock Chevy temperature gauge works by using a potentiometer to see a specific...
Common questions

What is the diagnostic code for a Chevy check engine light?

What is the diagnostic code for a Chevy check engine light? Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code list for definitions on all other Chevy diagnostic trouble codes. Manufacturer Specific Codes P0342Camshaft Position Sensor A Bank 1 Low Input - Related Information P1031HO2S Heater Current Monitor Control Circuit Sensors 1 How to reset the service engine light in a Chevrolet S10? You can reset the service engine light on your Chevrolet S10 by using an OBD-II scan tool. This on-board diagnostic tool can be purchased from your local auto parts retailer, although many...
Easy tips

How to set timing on Vortec 5.7 CarGurus?

How to set timing on Vortec 5.7 CarGurus? YOU MUST USE A SCAN TOOL TO SET TIMING ON VORTEC 5.7 Here at our repair shop we have the factory GM tech2 scan tool. You will be able to read the timing degrees with that. If the timing is off by more than 2 Degrees it will set a check engine light. Once you have the timing correct, you MUST do a procedure called (cam crank variation re-learn). What are the timing marks on a 1997 Chevy C / K 1500? - Almost two years to figure out that a 1997...
Easy tips

How do you reset the tire sensors on a GMC Sierra?

How do you reset the tire sensors on a GMC Sierra? Uplevel DisplayScroll down to the TIRE PRESSURE menu.Press and hold the thumbwheel button until the horn sounds twice to enter the relearn mode.Start from the driver side front tire, place the TPMS Relearn Tool against the tire sidewall, near the valve stem. A horn chirp will confirm that the sensor has been reset. How to fix the lock icon on the dashboard? Try this: Turn key to ON. Disconnect negative battery cable for about one minute. Take key out, lock doors and close them. Reconnect cable. Start truck. BTW,...
Easy lifehacks

Why is the starter on my GMC Sierra not working?

Why is the starter on my GMC Sierra not working? If your Sierra is not starting, don’t assume right away that the starter is bad immediately. There are other issues that can keep it from turning over. These include a bad battery, battery cables, or a neutral safety switch issue. Starters are not expensive, but replacing them can be tricky. What should I do if my Sierra does not start? Place the black lead of the multimeter on the negative battery terminal. If the battery reads less than 12 volts, charge it or replace it. If the battery reads higher...
Most popular

When did GM stop making Saturn Vue SUVs?

When did GM stop making Saturn Vue SUVs? It’s true, due to an agreement in 1999 some GM made Saturn Vue SUV’s came with Honda V6 engines between 2004-2007. Cars and what they have in terms of chassis, engine, and technology combos succinctly reflects the time period and who owned what of the time and that’s the case when it came to 2004-2007 Saturn Vue’s equipped with V6 engines. What kind of engine does a Saturn Vue have? Due to an engine swap agreement between GM/Isuzu and Honda in 1999, at an undisclosed time in the near future, Isuzu would...
Most popular

What kind of 4WD does GMC Sonoma have?

What kind of 4WD does GMC Sonoma have? We have a 2001 GMC Sonoma, ZR2 with the push button 4wd. The last two times that I have gone out and started the truck, it has been in 4 hi even though it was in 2wd when I parked it. From what I can tell, the 4wd is engaged, but it goes back into 2wd with no problems when I push the button. Why is my 4WD not working in my GMC Sonoma? When I got back to my cabin, I engaged 4WD again (indicator light is on) and put the...