Common questions

What is a code po301?

What is a code po301? P0301 indicates that cylinder number 1 is experiencing misfires. A misfire occurs when an insufficient amount of fuel is burning in a cylinder. A misfire from one or more cylinders can be caused by many reasons from a faulty ignition system, fuel system, or internal engine failure. What do the codes p0301 and p0316 mean? I went to get my emissions done and got the following codes P0301 cylinder #1 and P0316 Eng misfire detected on startup-1st 1000 Rev what does it mean and how do I fix it asap P0301 means misfire detected on...
Other

How many miles does a 2001 Ford Econoline drive?

How many miles does a 2001 Ford Econoline drive? 1st owner purchased on 05/24/01 and owned in HI until 03/31/14 • 2nd owner purchased on 03/31/14 and owned in HI until 12/10/15 • 3rd owner purchased on 12/10/15 and owned in HI until 02/09/21. 1st owner drove an estimated 5,064 miles/year • 2nd owner drove an estimated 0 miles/year • 3rd owner drove an estimated 10,724 miles/year. How much does a Ford Econoline cargo van cost? TrueCar has 413 used Ford Econoline Cargo Van s for sale nationwide, including a E-150 Recreational and a E-150 Commercial. Prices for Ford Econoline...
Easy lifehacks

What causes death wobble in F250?

What causes death wobble in F250? Ford Motor Company), says the death wobble is caused by a defect linked to abnormal wear or loosening of the track bar bushing, damper bracket, ball joints, control arms, shocks or struts. This often results in Ford failing to honor the truck's warranty through no fault of the owner. Why does my Ford F250 have death wobble? Read our story. Our Ford F250 4×4 began to experience the ‘ death wobble ‘ at around 80,000 miles. It is a stock vehicle with no lift or big tires. After several thousand dollars in repairs and...
Common questions

Should AC condenser be replaced?

Should AC condenser be replaced? A variety of things, including debris, impact and corrosion, can damage a coil. Because this is such an integral part of the overall component, a damaged coil instantly compromises the entire AC unit. If your condenser coil is out of warranty, it's best to consider just replacing the entire AC unit. What causes an AC condenser to go bad? Causes of a Bad A/C Condenser The main cause of a failing A/C condenser is simple wear and tear of the seals and tubes in the part caused by aging. Unfortunately, since the seals alone cannot...
Easy tips

Is there a way to test a dimmer switch?

Is there a way to test a dimmer switch? Unlike ordinary receptacles, a dimmer has wire leads instead of line and load terminals. If you believe that a dimmer switch may be faulty, test the device to ensure that the problem lies with the dimmer switch and not circuit connections. Replace any faulty dimmers with working ones as soon as possible. Where are the pins on the headlight dimmer switch? If you disconnect the Gray connector from the instrument panel harness... you'll notice that the Gray connector has the numbers 1 through 13 embossed on one side (see image 2...
Easy tips

Where is the SecuriCode code on a Ford Escape?

Where is the SecuriCode code on a Ford Escape? You will need to remove the trim panel for access to the fuse box, pull the panel toward you and swing it out away from the side and remove it. Securicode Keyless Entry Door Keypad Code located on a black & white sticker attached to the fuse box, it is 5-digit followed by a letter. Where is the fuse box on a Ford Escape? On the 2013-2020 Ford Escape, the passenger fuse box is located on the passenger side below the glove box. You will need to remove the trim panel...
Easy tips

Does a 1995 Ford Ranger have an OBD2 port?

Does a 1995 Ford Ranger have an OBD2 port? The port is 16 pins but it appears only 6 are in use. What scanner should be used on this vehicle? some 95 vehicles have the obd II port and will function but will give codes in obd I format. i suggest a shop that has the correct scanner. Where is the OBD connector on a Ford Ranger? OBD connector location for Ford Ranger (2006 - 2011) You will find below several pictures which will help you find your OBD connector in your car. The OBD connector is located under the...
Common questions

Why is the fan not working on my Mustang?

Why is the fan not working on my Mustang? If you do not have power and the relay swap did not work, then you will need to have the computer checked to see if its able to turn on and off the fan using a dealer scanner. The problem is most likely the relay or fan motor. The statements expressed above are only for informational purposes and should be independently verified. What should I do if my AC Fan does not turn on? With the engine running and the A/C turned on, check for power getting to the low or...
Other

What should fuel pump pressure be on a Ford van e-250 5.8?

What should fuel pump pressure be on a Ford van e-250 5.8? I have a 96 Ford e-150 conversion van with a 5.8 liter engine. The alternator is 130 amp. I had to replace it and used a 130 amp from a 93 ford explorer with a 5.8 liter engine. I installed it and eng … read more Have ''96 e-250, 5.8 that engine just stops, like kill switch. What kind of engine does a Ford van E-150 have? We have a 1994 ford van E-150 Chateau with 5.8 v-8 engine with auto. trans and all power. It has served...
Common questions

Does the front drive shaft spin in 2 wheel drive?

Does the front drive shaft spin in 2 wheel drive? No, your front driveshaft will not spin freely in 2wd. Your front axle and driveshaft are always locked and spinning when your vehicle is moving. When you engage the 4wd in the transfer case it then gets power transfer along with the rear wheels. Should I be able to turn the front drive shaft by hand? The simple answer is the front axle never disengages from the axle shafts, the gears, or the driveshaft. The only thing that disconnects is the transfer case. So you can't turn the front driveshaft...