Easy lifehacks

What should I do when my transmission is removed?

What should I do when my transmission is removed? Once the transmission is removed from the vehicle, contact several transmission repair shops and/or independent transmission technicians to obtain rebuild quotes for a “ bench job “. “Bench job” is the term used for a transmission rebuild only, not the labor to remove and install the transmission. Can a rear main seal be replaced without removing the transmission? You may choose to change other seals or gaskets or do any sort of engine rebuild, and then the costs of the parts can easily be accumulated up to a few hundred dollars...
Common questions

How much horsepower can a Dodge 360 handle?

How much horsepower can a Dodge 360 handle? After-market support for the 360 is great, and with the right parts, it can easily make 450 horsepower and still have great street manners. If you need more inches, it's easy to drop in a stroker crank and get 406 cubic inches. How much horsepower does a Dodge 360 engine have? Later models, such as the 360 four-barrel engine, which had a horsepower of 220, generally had more horsepower than the earlier ones. The Dodge 360 engine was produced from 1971 to 2002 by the Chrysler Corporation. The Dodge 360 was a...
Easy lifehacks

What causes a car to run rough idle?

What causes a car to run rough idle? When this vacuum is sealed, your car will run at optimum speed, performance and efficiency. If there is a leak in this vacuum, the ability for your car to gain energy from the burning fuel is compromised, causing rough idling. In the short term, a vacuum leak is a relatively easy fix. Left untouched, a leak can cause some serious problems. What does it mean when your car Idles smooth? Smooth idling indicates that your engine's fuel and air are mixing just right. What is rough idling? If your vehicle's idle is...
Common questions

Why does my brake pedal push against my foot?

Why does my brake pedal push against my foot? If the pedal pushes back against your foot, then there is a problem. This could be a blocked vacuum hose, a leak in the vacuum hose, or a leak in the brake booster check valve. Given that it happens after the engine has been idle for some time, inspect the check valve for leaks. Was this answer helpful? What to do when your brake pedal becomes Rock Hard? Check if the vacuum brake pump is connected properly or is even working Park the car and turn off the engine. Start the...
Easy lifehacks

How tall does a 518 overdrive transmission have to be?

How tall does a 518 overdrive transmission have to be? The top half of the transmission-crossmember had to be completely removed, otherwise the transmission couldn’t be mounted high enough in the car. The 518-transmission also come stock with a deep oilpan, so to keep enough ground-clearance, a proper transmission height was mandatory. Which is better a 904 or A518 overdrive transmission? Because an A518-transmission is more bulky than the 904, some considerable modifications are needed in the car like the driveshaft-tunnel and rear transmission crossmember. This is because these overdrive transmissions weren’t available on these cars and years yet. Is...
Easy lifehacks

What causes the OBD-II code ” p0505 “?

What causes the OBD-II code " p0505 "? P0505 is an OBD-II generic code that the engine control module (ECM) determined the engine idle control system is not managing the idle to stay in specification. The idle is too high or goes too low. What causes the P0505 code? The idle air control (IAC) valve is carboned up and sticks or has limited control due to the carbon build up. What causes the IAC to set p0505 at idle? Can be a three or four wire sensor depending on the model. The PCM monitors voltages of the IAC circuits and...
Easy tips

What does check gage mean on my Ford Ranger?

What does check gage mean on my Ford Ranger? The check gauge light on Your Ford Ranger usually relates to a gas tank issue. The most common cause is low fuel, but it can also be related to temperature or oil pressure. This light illuminates when the engine coolant temperature is high, the engine oil pressure is low or the fuel gauge is at or near empty. What to do when your car gauges are not working? The fuse should have power on both sides when the ignition key is turned to the on position. You can check this with...
Easy lifehacks

How does the p0720 output shaft speed sensor work?

How does the p0720 output shaft speed sensor work? P0720 Description. The speed sensor detects the revolution of the idler gear parking pawl lock gear and emits a pulse signal. The pulse signal is sent to the Transmission Control Module (TCM) which converts it into vehicle speed. What is the diagnostic code for input speed sensor? P0715 is a diagnostic trouble code (DTC) for "Input/Turbine Speed Sensor Circuit Malfunction". This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. What does p0717 input turbine speed sensor...
Most popular

How many 4X4 Rumble Bees were made?

How many 4X4 Rumble Bees were made? In the first year of production, only around 3,700 units of the trucks were made and sold. From the years 2004 - 2005, only around 8,700 Dodge Rumble Bees were produced by the company. After this period, the second swarm of about 5,000 units was produced and sold. What causes a 2004 Dodge Ram 1500 to stall? Some 2004 Dodge Ram 1500s stall when braking and at idle, as well. The most common report is that on a cold start, the truck won’t move when put in gear. The transmission may also slip...
Other

How do you check the transmission fluid on a Dodge Caliber?

How do you check the transmission fluid on a Dodge Caliber? How to Check the Transmission Fluid Level in a Dodge CaliberDrive the Caliber for 10 minutes or allow the engine to idle for 20 minutes. Remove the transmission fluid level indicator (dipstick) from the slot on the right side of the engine. Wipe the dipstick clean with a paper or cloth towel. Where is the dipstick tube on a Dodge Caliber? The dipstick tube has a cap and is at the front of the engine near the fresh air intake. I've been told by one deale it never has...