Most popular

What transmission is paired with the 2.5 L iVCT I-4 engine on Transit Connect?

What transmission is paired with the 2.5 L iVCT I-4 engine on Transit Connect? Both engines feature standard Auto Start-Stop and are paired with a new 8-speed SelectShift® automatic transmission. Fleet customers can opt for a 2.5-liter iVCT I-4 gas engine with CNG/LPG gaseous fuel prep package. Which is a benefit of side wind stabilization? CWS assists drivers in controlling a vehicle during strong wind conditions such as driving over a bridge or when overtaking a semi-truck. What kind of engine does Ford Transit Connect have? The van's standard turbocharged 2.0-liter four-cylinder makes 150 horsepower and 144 lb-ft of torque...
Other

What does the blend door actuator do on a F-250?

What does the blend door actuator do on a F-250? The blend door actuator is responsible for controlling the hot and cold air mixtures in your Ford F-250 or F-350 Super Duty. Where is the temperature controller on a Ford F-250? Automatic Temperature Control-equipped dual zone trucks have two; the second actuator is low, located above the transverse air duct. Does the temperature controller work? The related article below provides instructions for testing the manual controller, a simple potentiometer. Can a car vent blow cold one side and hot the other? In a vehicle with dual temperature controls you may...
Common questions

Where can I get an OBD2 scan for my car?

Where can I get an OBD2 scan for my car? An OBD2 reader is an affordable scanner that is available in any auto shop or hardware store. When you take your vehicle for a check engine light scan, mechanics usually use this OBD2 reader for their diagnostics. An OBD2 reader uses Diagnostic Trouble Codes (DTC) that trigger your vehicle to indicate when something isn’t working properly. Which is the best OBD2 scanner with ABS and SRS? FIXD is a great obd2 scanner with abs and srs, an easy-to-use device that is built for everyone. If you are tired of bringing...
Common questions

How do you tell what year a Ford pickup is?

How do you tell what year a Ford pickup is? Identifying a Ford truck model year can be done using the VIN or Vehicle Identification Number. The VIN is a series of 17 letters and numbers for vehicles manufactured after 1982. VIN numbers prior to 1982 can be decoded by a local Ford dealer. What does the VIN number on a Ford Ranger mean? Ford RANGER VIN decoder Every Ford car has a unique identifier code called a VIN. This number contains vital information about the car, such as its manufacturer, year of production, the plant it was produced in,...
Easy lifehacks

Why is my HVAC blower not turning on?

Why is my HVAC blower not turning on? So when calling for cooling, the thermostat usually energizes both Y for cooling, and G to turn on the blower. Since you say the blower doesn't come on for cool calls, or when the fan switch is moved to the ON position. That points to a problem with the "fan circuit". What to do when your HVAC fan won't work? Since the blower works for heat, you might try putting the wire that's on the HEAT terminal on the COOL terminal. If the blower fires up, you know it's a problem with...
Easy tips

Which is Ford 3.5 jumped the timing chain?

Which is Ford 3.5 jumped the timing chain? FORD 3.5 3.7 JUMPED TIMING CHAIN. FORD EDGE, FLEX, EXPLORER, FUSION, F150, TAURUS - YouTube If playback doesn't begin shortly, try restarting your device. How do you remove phaser from Ford F150? Removing cam phaser bolt. With the bolt removed, slightly lower the phaser to allow slack in the timing chain and carefully remove the timing chain from the cam phaser sprocket teeth before removing the phaser from the engine. How is the phaser attached to the timing chain? The phaser is aligned with a dowel pin, so it will only go...
Common questions

What is the main bearing Torque?

What is the main bearing Torque? On the 3.0L engine, the main bearing cap bolts should be torqued in proper sequence to 14 ft. lbs. (20 Nm), then an additional 90 degrees and another 45 degrees after that. Also on the 3.0L engine, the connecting rod cap nuts should be torqued in proper sequence to 22 ft. What is the torque value of a connecting rod? Torque Value: Step 1 149 n.m [110 ft-lb] Step 2 Rotate 180 degrees Used Connecting Rod Capscrews Used Connecting Rod Capscrews Hand-tighten the capscrews in. Tighten the capscrews : 70 N•m [52 ft-lb]. Check...
Easy tips

Can a Ford F 350 6.7 diesel start?

Can a Ford F 350 6.7 diesel start? I have a ford f 350 6.7 diesel wont start the codes it has po627 fuel pump A control circuit open. Not sure it had I have a ford f 350 6.7 diesel wont start the codes it has… Why does my Ford F350 crank but not start? If your F350 isn’t getting enough fuel, or any fuel at all, it may have a bad fuel filter, bad fuel pump, or bad fuel injectors. Without the proper amount of fuel getting into the combustion chamber, the F350 will crank, but not start....
Common questions

Why is my brake pedal sticky?

Why is my brake pedal sticky? One of the most common causes of sticking brakes is simple: stuck brake calipers. Most vehicles use disc brakes, which include brake pads, rotors, and calipers. If the brake caliper gets stuck, you'll notice a sticky sensation in your brakes. Have the brake caliper assembly replaced to solve the problem. Why does my brake pedal not come back up? Brakes 1993 f250 4x4 , the brake pedal doesn't fully return. Brakes drag, lights come on in middle of night. New booster and master. Brakes bled. Any … read more Hi - my brake pedal...
Easy lifehacks

What is quiet start on Ford F-150?

What is quiet start on Ford F-150? The Quiet Start feature enables a lower warm-up RPM when you use the remote start. Having this feature OFF when you remote start it, the engine will start and idle at about 900 RPM to warm up faster. Why is my Ford F-150 making a noise? But, as the F-150 and I rounded the corner into 2019, a noise developed from the engine bay. When the engine and engine oil were cold, I observed a rattle coming from the top of the engine every time I accelerated to 2,500 rpm and lifted off...