Most popular

When did the Ford Bronco 2.8 come out?

When did the Ford Bronco 2.8 come out? The 2.8 used a carburetor and was available only in ’84 and ’85; replaced by the 2.9 for 1986. Through its run, a total of seven different transmissions were used — a list that included four- and five-speed units from Mazda, two five-speeds from Mitsubishi, and three- and four-speed automatics made by Ford. What was the problem with the Ford Bronco II? Engineers suggested changes to increase stability, but execs declined. They decided delays to Bronco II’s launch were unacceptable. Suddenly, most of the information (53 reports) collected by Ford’s legal department...
Easy lifehacks

What holds the battery in place?

What holds the battery in place? Maybe you have a different name for it — base clamp, brace, “that thing that keeps my battery secure.” Whatever you call it, the battery hold-down keeps your battery from moving as your car goes up and down hills, around corners and through quick starts and panic stops. How can I keep my car battery in place? Check out the seven tips below on extending the life of your car battery:Limit Short Rides. Keep Your Battery Tightly Fastened. Turn Off All the Lights When You Exit. Control the Corrosion. Test Your Battery Often. Don't...
Most popular

Why are the lights on my Ford Edge not turning off?

Why are the lights on my Ford Edge not turning off? The interior lights of my Ford Edge will not turn off. What can I do? I have checked all doors and the hatch and tried The interior lights of my Ford Edge will not turn off. Why does my Ford door light not shut off? Over time there is no amount of door slamming that can get that always-on, retina-burning, constant-reminder-of-your-decision-to-buy-a-Ford to shut off. It’s most likely an electrical issue related to the switch inside the latch mechanism. When does the interior light turn off on a Ford Escape?...
Easy tips

How do you adjust intake valve on hydraulic lifter?

How do you adjust intake valve on hydraulic lifter? For Hydraulic Lifter Camshafts When the exhaust valve just begins to open on the first cylinder in the firing order, adjust the intake valve by loosening the adjusting nut slightly while spinning the pushrod until you feel lash in the rocker arm. Tighten the adjusting nut until the slack is taken out of the rocker arm and pushrod. When do you switch to an adjustable valvetrain? If we switch to solid lifters it is mandatory that we convert to an adjustable valvetrain (I would also say that converting to adjustable valvetrain...
Common questions

What was the name of the 1959 Ford Galaxie?

What was the name of the 1959 Ford Galaxie? This 1959 Ford Fairlane 500 Galaxie Sunliner is a fantastic example of Ford's top of the line model The "top of the line" model for Ford's full size line up in 1959 was the Galaxie.. 1959 Ford Galaxie 500 Starliner Convertible. When did the Ford Galaxie 500 come out? On December 19, 1959 the Northrop's traded their 1957 Ford Skyliner for a brand new 1959 Skyliner a 1959 Ford Galaxie 500 Convertible Only 500 miles on nut and bolt body off frame restoration on a ro This 1959 Ford Galaxie represents...
Other

How to install solenoid valve in Ford 6F35?

How to install solenoid valve in Ford 6F35? Valve Body 6b Plastic Checkballs 6a Solenoid Valve Body NOTE: The components in this kit are all related to the valve body. It is not necessary to remove pump for kit installation; pump should only be removed if vacuum testing pump locations is desired. Drill solenoid pressure regulator balance hole and seal with .062" Why do you need a full manual valve body? TCI® Full Manual Valve Bodies allow for quicker shift timing and the ability to run higher line pressures than with an automatic shift. Designed for maximum performance & quick...
Easy tips

Should I disconnect battery before changing spark plugs?

Should I disconnect battery before changing spark plugs? No. The battery will not cause any problems when changing the plugs. The one thing to avoid is accidentally dropping a tool and having it contact the positive battery terminal and the car body. If this occurs, you will get a spark and possibly blow a fuse. How long does it take to change a ignition coil? Maybe 30 minutes, Maybe a few hours, it depends on what type, single coil and distributor in an older car, or separate coil for each plug in most modern ones. The coil may be easily...
Common questions

How much can I tow with a 2001 Ford F250 crew cab?

How much can I tow with a 2001 Ford F250 crew cab? On the F250 it is based on spring rating. The axle under your truck is rated for 7200lbs, if your wheel are aluminum they should be rated for 6000lbs (3000 each), and the tires will be size dependent (LT235/85R16 LRE 6084lbs per pair, LT265/75R16 LRE 6830lbs per pair). Of course springs can be changed or air bags added. What kind of tow rating does Ford F250 have? All of the newer Ford trucks (2005 and up) have higher ratings.SRW F250's and F350's have the same tow ratings and...
Easy tips

Why does my Ford Explorer have a p0430 trouble code?

Why does my Ford Explorer have a p0430 trouble code? There are many things that can cause the P0430 trouble code in your Explorer. Here are the most common ones. Oxygen Sensor – The P0430 codes is thrown when the oxygen sensors on both sides of the exhaust have very similar readings. When the oxygen sensor is bad, it can cause a false reading and trigger the code. What is the OBDII code on a Ford Explorer? One of the most common trouble codes with all Ford vehicles is the P0430. This code number references a number that is given...
Most popular

Do you need a locksmith for a Ford F150?

Do you need a locksmith for a Ford F150? At present, supplement Ford F150 PAT keys has to be done through a a commissioned locksmith or an accredited dealer and the key has to be compatible and decosed to the motor vehicle and essentially replicating keys become more regulated and as a side effect also way more high pricing. How to program new keys for Ford F150? Ford F150: How to Program New Keys 1 Step 1 – Insert programmed key. Before programming the new key, first insert the already programmed key into the ignition, then turn it ON and...