Most popular

How much horsepower does a straight 8 have?

How much horsepower does a straight 8 have? The new eight featured low-compression (usually between 7.00:1 and 8.00:1 ratios), long-stroke (usually between 4 1/4-inches and 4 5/8-inches), and 125–160 hp. These were silky smooth and easily propelled the mammoth 5000-pound cars from a dead stop in high gear—which was rumored to have been advised by dealers. Is V8 better than straight-8? Inline-eight engines are much longer than V8 engines of comparable displacement, and therefore use the available size much less efficiently. Inline-eight engines also aren't possible to build in a perfectly harmonically balanced configuration, as is possible with a cross-plane...
Common questions

Where do you put brake fluid in a Ford Ranger?

Where do you put brake fluid in a Ford Ranger? It is usually in the back of the engine bay, on the driver's side. Cover the fender before opening the brake master cylinder and use caution when opening a container of brake fluid, as it can damage your vehicle's paint. Where do you put brake fluid in a 2003 Ford Ranger? The 2003 Ford Ranger uses DOT 3 brake fluid. The reservoir can usually be located on the drivers side of the engine bay towards the rear. Brake lubricants work with the Ranger's heavy shoes, rotors and pads to absorb...
Easy lifehacks

What was the elapsed time for a 1957 Corvette?

What was the elapsed time for a 1957 Corvette? Power was generated smoothly and at an increasing rate until about 2800 rpm when the cam hit its stride and the car hunkered down and steamed into the distance. Elapsed time for 14 to 60 mph in high was 12.3 seconds, on the injected machine. The same continuous flow of power held good during hard cornering and braking. Who was the builder of the 1957 Corvette? To find out, we set up a full transcontinental '57 Corvette road test, involving our entire testing staff. On the West Coast an injected machine...
Easy lifehacks

Where do I find the engine type code?

Where do I find the engine type code? The engine model and serial number should be adequate for most of your needs. However, if you need the detailed engine type, you can find an engine identification guide here. The engine type code is stamped into the side of the engine, usually close to the serial number. Engine type codes may be up to 4 characters. How can I find out what kind of engine my car has? It’s also interesting to see how much horsepower and torque its capable of, as individual engines can vary from the figures quoted by...
Easy lifehacks

Is there a 1965 Ford Fairlane coupe on sale?

Is there a 1965 Ford Fairlane coupe on sale? Original, un-restored cars from the 1960s are becoming harder and harder to find. Even if they aren’t mint, it’s nice to be able to start with cars that haven’t been “messed with.” This 1965 Ford Fairlane Sports Coupe fits that definition, only has two doors to satisfy the coupe-only folks, and is available for sale here on eBay without a reserve. Is the Ford 302 good for Trans Am racing? The new Ford 302 would be ideal for Trans-Am racing since it was under the 305 cid limit of class limit,...
Most popular

How do I identify a 442?

How do I identify a 442? From 1968 to 1971 the VIN will identify if the car is a factory 442. You're looking for a 344 in the start of the VIN on dash or door decal. This signifies an Olds 442 model. The next two numbers afterwards should decode to either a hardtop, pillar coupe or convertible. Is a Hurst Olds a 442? The first Hurst/Olds was the 1968 Hurst/Olds. It shared its body with the regular Oldsmobile Cutlass and 442, but had a unique Peruvian Silver and Black paint scheme. 515 production examples of the 1968 model were...
Common questions

How to remove gear from shaft without gear puller?

How to remove gear from shaft without gear puller? The gear will come off easily if you heat it. You will need a small butane torch (you can buy one on Ebay for five bucks or so). Get the gear glowing hot, and then use screwdriver or something similar to push it off the shaft. Then heat it again before sliding it onto the shaft of the new motor. And yes,... How do you remove gear from a brushless motor? The gear will come off easily if you heat it. You will need a small butane torch (you can buy...
Easy lifehacks

How to install a horn button on a GM steering wheel?

How to install a horn button on a GM steering wheel? The folks at Ididit, Inc. put together a video showing the installation of a horn button on a 1955-68 GM steering wheel and horn button onto one of their Ididit, Inc. steering columns. The video starts out by showing the necessary tools you would need to install the steering wheel and horn button kit onto the column. Where do you put the Horn hole on a car? The horn hole should be placed at or as close to the 10:30 position as possible to line up with the horn...
Easy lifehacks

What kind of grille does a 1967 GMC pickup have?

What kind of grille does a 1967 GMC pickup have? All new 1967 GMC pickup truck steel grille assembly. This grille is designed to be painted to match your color scheme. Note: This item is oversized and is a special order. This will ship in its own box and cannot be combined with other items. 67-68 Chevrolet pickup truck chrome grille frame. What kind of front grille does a Chevy truck have? USA1 Industries Chevy Truck Parts offers high quality the 1977-80 Chevy Truck Front Grille without Bowtie Emblem in the correct black finish. Metal clip that pushes onto your...
Easy lifehacks

Why does my car vents smell like gas?

Why does my car vents smell like gas? When there are more gas fumes coming out of your exhaust, it's possible that these fumes will make their way into your ventilation system, which is why you would smell gas inside of your car. In addition to the odor of gasoline, decreased fuel efficiency and engine power are also signs of a bad fuel pressure regulator. Why is gas coming out of the vent on my Boat? It was difficult to put gas in the tank. The nozzle continually shut down, as if the tank were full, until a gusher of...