Other

How do you check teeth on flywheel?

How do you check teeth on flywheel? Just take the inspection cover off and use a ratchet and socket on the crank pulley to turn it over and check the teeth. If they're are missing teeth and this is a flywheel and not a flex plate you can flip the ring with the teeth on it and reuse the flywheel... How do you heat ring gear? 1) Heat oven to ~400*F. 2) Put ring gear in oven for 45-60 minutes (you want to heat it all the way through.) 3) Keep carrier handy. 4) Lower ring gear onto carrier while...
Easy tips

What happens when you remove all the bolts on a torque converter?

What happens when you remove all the bolts on a torque converter? Continue to turn the crankshaft until all three or four bolts are removed. Most vehicles use four bolts, but some have only three. When all are removed, the torque converter can be moved rearward. Why do we use torque to create tension? Torque is used to create tension. Bolts are used to affix two components so that they can resist tensile (pulling apart) and shearing (sliding apart) forces. After the nut has been turned onto the bolt, additional torque causes the nut to turn and stretch the bolt....
Most popular

What causes a motor to stall at locked rotor?

What causes a motor to stall at locked rotor? 2. Mechanical reason: Rotor jam, overload or load unable to move. Stall current is the current drawn by the motor at locked rotor condition. It is the highest current a motor can draw and is proportional to its rotor resistance. If stall current is drawn by a motor for a longer time, motor gets overheated causing damage of winding. When is it time to turn your rotors? If your rotor surface is smooth, then you might not require the turning rotors to take place. However, if you have warping or tough...
Easy lifehacks

What do position sensors ( CKP ) and CMP do?

What do position sensors ( CKP ) and CMP do? Modern computer-controlled vehicles must have the air and fuel ignited at the proper instant in order to operate. Both (CKP)- (CMP) position sensors are part of your car’s electronic fuel injection and ignition system. In the old days, if you had fuel, spark and were close to correct in timing, your engine would run. What to do if your CKP sensor is failing? Consider it an additional warning that the (CKP)- (CMP) sensor is failing, especially when coupled with: An engine light diagnostic tool can pinpoint the problem, enabling you...
Other

What does the P0420 code on the oxygen sensor mean?

What does the P0420 code on the oxygen sensor mean? Here's how to modify your car's oxygen sensor to get rid of a P0420 OBDII code, clear the check engine light and pass an emissions test. The P0420 code is thrown when the computer detects irregularities in the signal coming off of the secondary oxygen sensor. When does an O2 sensor set a trouble code? If it’s not switching rapidly, the ECM will set an O2 sensor related trouble code If the upstream and downstream oxygens sensors are both switching from rich to lean, that’s the sign of a dead...
Easy tips

Why does my Chevy Impala not shift out of Park?

Why does my Chevy Impala not shift out of Park? This results in one or more of the following symptoms, depending on which wire is disconnected: 1. The car will not shift out of park. 2. The key will not release from the ignition. Remove the center console to determine if one of your wires is broken or disconnected from the clip. If so, this fix should work well for you. 1. What do you do when your shifter is stuck in Park? By law, all 2010 and newer vehicles are equipped with brake-shift interlock. 1) Set the emergency brake....
Common questions

How good is a Chevy Impala?

How good is a Chevy Impala? The Chevrolet Impala is a great car. It offers more passenger and cargo space than most in the large car class, and its infotainment controls are easy to use. Its muscular engine and gentle ride only boost its appeal. Is the GM 3900 a replacement for the GM 3800? All of the engines in the High-Value series have 60-degree overhead valves. GM manufactured the 3900 V6 as a replacement for the GM 3800 V6. How many valves does a GM 3900 V6 have? The engine has two valves per cylinder. The 3900 V6 also...
Common questions

How do you fix a leaking door frame?

How do you fix a leaking door frame? How to Fix Door Jamb Air LeaksRemove molding or trim from one side of the door using a pry bar and hammer. Squeeze water-proof caulk into cracks in the door fame to seal out both air and moisture. Replace molding or trim. Install weatherstripping around the top and sides of the doorjamb. Why is my door leaking? The common problems that can cause doorway leaks include: Lack of adequate caulking around the doorway. Cracked or deteriorated weather stripping. Improper installation of weather stripping. How do you fill gap between door and casing?...
Easy lifehacks

What kind of bench seat does a Chevy Blazer have?

What kind of bench seat does a Chevy Blazer have? 1981-91?? Chevy GMC Blazer Jimmy Suburban K5 Rear 3rd Row Seats Gray Seat 1994 CHEVY 2500 EXT. CAB FRONT SPLIT BENCH & REAR CLOTH SEATS LIGHT GRAY 13D Only 1 left! Where does GMC Truck bench seat foam come from? Our cushions are manufactured in the US with a precision cold cure molding process that exceeds original quality and is fleet tested and reinforced with a tough Polypropylene mesh. Score: 5.00. Votes: 1 It is beyond very nice to be able to refurbish my truck with parts that are just...
Common questions

Can you remove a turbo from a diesel engine?

Can you remove a turbo from a diesel engine? No, It will not work properly. By removing turbocharger, you are reducing the total amount of air supply per intake stroke of engine. But the amount of diesel per stroke is remaining the same. So, the amount of oxygen present will not be able to burn the total diesel. Can I disconnect my turbo? There's no concept of “disconnecting” the turbo as it's an integral part of both the exhaust and induction systems, so the short answer is NO. There's no concept of “disconnecting” the turbo as it's an integral part...