Easy tips

Can a 6 month old gasoline cause a car to not start?

Can a 6 month old gasoline cause a car to not start? Nope. Don’t blame 6-months-old fuel. Adding fresh fuel is unlikely to help. To prove my statements, get a spray can of QuickStart or equivalent. If your car still won’t start and run using the spray, your problem is definotely not due to old gas. What to do if your car wont start with bad gas? If your car won’t start and you know it’s caused by bad gasoline: You will need to take your car to a trusted repair facility. A fuel octane booster, like Sea Foam or...
Most popular

Can a 4 speed Muncie be used as a 5 speed?

Can a 4 speed Muncie be used as a 5 speed? Looking at it closely, with a bit of work, you could use mostly all of your existing 4spd Muncie stuff, even the cross member and perhaps the driveshaft. Depends some on how your car is built now. The overdrive 5th gear is best with a motor that has some low/mid range torque. What kind of transmission does a 1965 C10 have? For instance, my 1965 C10 factory 3 speed transmission has a 2.95 1st gear coupled with a 3.73 rear differential and it came with a 6 cylinder engine....
Easy tips

What kind of ignition switch does a 1997 Chevy Tahoe have?

What kind of ignition switch does a 1997 Chevy Tahoe have? This tutorial will help you test the ignition switch on the 1997 Chevrolet and GMC Pick Up, Suburban, Tahoe, and Yukon equipped with a 4.3L, 5.0L, or a 5.8L V8 engine. The ignition switch test involves checking for continuity across specific terminals of the ignition switches connector. Where is the ignition switch on a 1997 GMC? Disconnect the ignition switch from the vehicle wiring harness connector at the base of the steering column. Place your multimeter in Ohms mode. Place the ignition key in the ACC position. You should...
Other

How to install a LS3 engine in a Camaro?

How to install a LS3 engine in a Camaro? Mary’s LS3 drops right in as if it were meant to be there all along. (Photo Courtesy Mary Pozzi) The installation of an LS engine can be done in the typical garage with jack stands, a solid and reliable engine hoist, and a host of typical hand tools. How to remove the front end of a Camaro? Remove a few bolts so the front end can be separated from the rest of the chassis. Several bolts hold the front clip to the subframe and firewall. In fact, several bolts connect to...
Easy lifehacks

What type of sensor is an accelerator pedal position sensor?

What type of sensor is an accelerator pedal position sensor? In this example, the Accelerator Pedal Position (APP) sensor is of the potentiometer type. It receives two reference voltages from the Powertrain Control Module (PCM), having two ground wires and two signal wires that send a varying voltage back to the PCM relating to accelerator pedal position. What are the sensors on the accelerator pedal? The two main sources of input data are the accelerator pedal position sensors (APP1 and APP2) and throttle position sensors (TPS). These sensors consist of a combination of two or more sensors, while the electronic...
Most popular

What tools do I need to change an oxygen sensor?

What tools do I need to change an oxygen sensor? Things You'll NeedNew oxygen sensors.Jack.Jack stands.3⁄8 in (0.95 cm) ratchet wrench or open end wrench.7⁄8 in (2.2 cm) oxygen sensor socket.Penetrating oil.Auto diagnostic scanner/reader (optional)Flathead screwdriver (optional) What's the best way to remove an O2 sensor? Spray the penetrating oil on the O2 sensor and allow it to sit for a good 20-30 minutes or overnight would be even better. Afterward, use an O2 sensor socket wrench to break loose the O2 sensor. Sometimes, due to tight spaces, you may have to use a regular metric or standard wrench. Some...
Easy lifehacks

How does a Chevrolet Avalanche door panel work?

How does a Chevrolet Avalanche door panel work? When you send a message to the car window, its the regulator that goes into action to move it. Your Chevrolet motor is a stationary device that provides the power to the regulator. When you hear the motor operating as you make adjustments on your vehicles door, that indicates the motor is working. What kind of window regulator do you need for a Chevy Avalanche? An ACDelco GM Original Equipment Window Regulator will keep your windows running properly and are a GM-recommended replacement for your vehicle's original components. This... Power Window Regulator...
Easy tips

Are there any issues with the Chevy tracker?

Are there any issues with the Chevy tracker? Other than that one issue, our Tracker has provided flawless reliability for 50K miles with just annual synthetic oil changes and lube. We wanted inexpensive, all-weather transport for commuting, and have not been disappointed. What kind of transmission does Chevy tracker have? Today i was on napa's website looking up filters for my 2004 tracker Zr-2, well under transmissions it Lists the tracker 2.5 v-6 as having a toyota transmission. Can anyone confirm this? I know the engine is Suzuki as the name is all over it. Why does my Chevy tracker...
Easy lifehacks

What is the dpfe sensor on a Ford F-150?

What is the dpfe sensor on a Ford F-150? Ford uses the DPFE Sensor a lot for their different car models. The most common car model is probably the F-150. EGR, which is short for “ Exhaust gas recirculation ” is a mechanism which controls precisely what the name suggests. The EGR system consists of a valve which controls the exhausted air getting back into the engine. How can I check if my dpfe sensor is working? Check the vacuum hoses: Check for cracks or broken hoses between the EGR and the DPFE sensor. Check the wiring: Use a multimeter...
Easy tips

How much is a front-wheel assembly?

How much is a front-wheel assembly? The average cost for wheel hub assembly replacement is between $475 and $504. Labor costs are estimated between $109 and $137 while parts are priced between $366 and $367. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed. When to see a mechanic about your wheel assembly? The reason for this is commonly due to a worn out wheel bearing inside the hub assembly. If you notice this symptom, it's recommended to contact a certified mechanic as soon...