Most popular

What causes a loud clicking noise during acceleration?

What causes a loud clicking noise during acceleration? Noise: Banging or heavy clicking every two to three feet during acceleration and deceleration Cause: Damaged or broken pinion gear tooth or teeth Noise: Banging or heavy clicking every two to three feet during acceleration or deceleration, but not both What causes a clunking noise on the driveline? Cause: Bad wheel bearings Noise: Driveline squeaking or grinding at any speed Cause:Worn or damaged U-joints Noise: Clunking when depressing the throttle pedal (takeoff) Cause:Worn U-joints; worn spider gears; worn axle splines; excessive gear backlash; loose yoke splines; worn slip yoke splines Noise:Clunk immediately...
Common questions

What kind of engine does a 1995 Chevy K have?

What kind of engine does a 1995 Chevy K have? Re: I have a 1995 chevy k 1500 350 tbi it hesitates when... Check if it has it; EGR valve and controls, throttle position sensor, and fuel pressure. Process of elimination. A real time scanner may be of help You can't post conmments that contain an email address. An expert that got 20 achievements. An expert that got 10 achievements. When was the last serviced Chevy C / K 2500? Last serviced at 117,880 miles in Mandan, ND on 04/24/18 • Vehicle serviced • Maintenance inspection completed • Fuel tank...
Common questions

What kind of transfer case is New Process 208?

What kind of transfer case is New Process 208? The New Process 208 is a chain-driven transfer case. This is a cast aluminum transfer case. Compared to the NP203 and NP205, the light-weight cast aluminum housing of this transfer case is easier to handle. Is the NP208 transfer case part time or manual? The NP208 was manufactured with manual shift, it is a replacement unit for the earlier units, it is a part time case, the front driveshaft will not receive power when in 2WD. The transfer case is, chain driven, 2.62:1 ratio reduction in low and 1:1 in high...
Other

How does the proportioning valve on a master cylinder work?

How does the proportioning valve on a master cylinder work? If equal braking force were applied to all four wheels during a stop, the rear wheels would lock-up before the front wheels. The proportioning valve only lets a portion of the amount of pressure to the rear wheels thus preventing rear wheel lock-up. Where is the proportioning valve on a car? The proportioning valve is mounted between the brake line master cylinder and the rear wheels. It's designed to adjust the pressure between the front and rear brakes, depending on how hard you're stopping. The shorter the stopping distance, the...
Most popular

Why wont my RPMs go down?

Why wont my RPMs go down? There likely is an issue causing the condition such as a vacuum leak, faulty idle air control, faulty wiring, loose or corroded connection in a plug, faulty sensor, a mechanical issue or perhaps an engine ventilation problem. Consider a trip to an experienced technician to have the cause of the trouble diagnosed. Why does my RPM drop when sitting idle at traffic lights? While I'm sitting idle at traffic lights I put the car into neutral. The engine stays idling at about 1000 RPM. However every now and then it drops down to about...
Easy lifehacks

How does the EGR work in a car?

How does the EGR work in a car? The EGR valve recirculates burned exhaust emissions back into the intake system so the emissions can be re-burned, or "recycled," out the exhaust. The system operates by the opening and closing of solenoid valves, regulated by a diaphragm. When to replace the EGR valve on a diesel engine? The EGR valve on a diesel engine usually gets a lot more dirt in it, and it has to be replaced and cleaned more often. The carbon build up can also destroy the EGR valve and you have to replace it more often. A...
Common questions

What to ask when interviewing a wire harness manufacturer?

What to ask when interviewing a wire harness manufacturer? Having a list of tough questions prepared brings tremendous value to the process. Since we are a Wire Harness Manufacturer, we will specifically address Interviewing a Wire Harness Manufacturer. At this stage, you have narrowed the field down to either a single or hopefully a few candidates. Now is time to begin the interview process. What should I look for in a harness inspection? Every harness must have a legible tag identifying the harness, model, date of manufacture, name of manufacturer, limitations and warnings. •Check tag for date of manufacture and...
Easy lifehacks

What do I need to reprogram a GM PCM?

What do I need to reprogram a GM PCM? Turn on the scan tool and load the TIS programming software from GM on your computer. Click the “Service Programming System” option on the main screen of your TIS software on your computer. The “Select Diagnostic Tool and Programming Process” window will appear on your screen. How do you change the programming on a Chevy PCM? Select “Normal” under programming type and click the “Next” button. Select the newest calibrations for each system in the “Calibration Selection” window by clicking on each system’s tab, and putting a check mark next to...
Easy tips

Why does my car stall at highway speeds?

Why does my car stall at highway speeds? The engine may start and idle fine, but run out of power or even stall at highway speeds. If the engine starts right back up after stalling, the likely cause is low fuel volume delivery because of a weak pump. If the engine is running normally one minute, but suddenly quits, loss of ignition may be the problem. What causes an engine to stall at idle? If the ISC valve is gummed up with fuel varnish or dirt, it may stick, preventing the engine from maintaining the proper idle speed when the...
Most popular

Where is the fuel filter in a 2005 Chevy Equinox?

Where is the fuel filter in a 2005 Chevy Equinox? The 2005 Chevy Equinox does not have a traditional fuel filter. Instead, it uses a filter screen which is integrated into the fuel sending unit, or fuel pump, which is located inside the gas tank. How can you tell if your equinox fuel filter is bad? There are physical signs that you can feel when your Equinox’s fuel filter is clogging. Before taking anything apart, check to see if your engines computer has any trouble codes saved in it. The engine may throw a P0087 trouble code. Where is the...