Other

How does the VSS work on a Ford F350?

How does the VSS work on a Ford F350? P0500 is a OBDII trouble code that affects the Ford F350 ‘s Vehicle Speed Sensor (VSS). The VSS sends a signal to the engine’s computer letting it know how fast that the vehicle is going. The F350 uses this signal for many vehicle functions. What happens when the VSS does not work? Speedometer Failure – Without a properly working vehicles speed sensor, the speedometer will not register any speed. It’ll just sit at 0 MPH while you are driving. The Odometer may not work at all. Cruise Control Failure – When...
Easy lifehacks

Is the Ford FE engine a big block?

Is the Ford FE engine a big block? The Ford 390 was a 6.4-liter (390.04ci) gasoline big block V8 engine that was produced between 1961 and 1976. The 390 was part of the Ford-Edsel (FE) engine family, which was produced from 1958 to 1976. What is a Ford big block FE? The Ford FE engine is a Ford V8 engine used in vehicles sold in the North American market between 1958 and 1976. The FE was introduced to replace the short-lived (in the USA) Ford Y-block engine, which American cars and trucks were outgrowing. "FE" derives from 'Ford-Edsel.' What kind...
Easy lifehacks

Why is the blinker on my car blinking so fast?

Why is the blinker on my car blinking so fast? Compare the left to the right side, and check both the front and rear of the vehicle. If all the bulbs are blinking, the same on both sides of the car, but one side is blinking fast, and the other side normal, then you do have a more complicated problem. What to do if your blinker blinks fast? Compare the left to the right side, and check both the front and rear of the vehicle. If all the bulbs are blinking, the same on both sides of the car, but...
Other

Why do I need to replace my timing chain tensioner?

Why do I need to replace my timing chain tensioner? The timing chain tensioner is responsible for keeping the proper tension on you timing chains. It does this by keeping constant pressure on the guide rail. If you are starting to get chain noises from the engine, especially on cold start ups you should inspect or replace the tensioner right away. When to replace timing chain rattle in 4.0 SOHC? ALL 4.0 SOHC OWNERS SHOULD REPLACE THE PLUNGER TYPE SCREW-IN TENSIONERS EVERY 70,000 MILES OR SO TO PREVENT CHAIN SLACK, WHICH KILLS THE GUIDES! If the rattle is ONLY on...
Common questions

Can You diagnose ABS / ESC hydraulic control units?

Can You diagnose ABS / ESC hydraulic control units? Some of the toughest vehicle components to diagnosis are ABS/ESC Hydraulic Control Units (HCU). Even in a “passive state” the HCU has to keep designated solenoids open or closed to allow the ABS system to be bypassed. How does the ABS system work on a car? The ABS system is made up of the ABS module, and ABS sensors at each wheel. The sensors detect wheel speed, and will send a message to the ABS module to rapidly pump the brakes when it is detected that the vehicle is skidding or...
Easy lifehacks

How long does a Ford SYNC Master Reset take?

How long does a Ford SYNC Master Reset take? approximately 10 minutes The master reset process takes approximately 10 minutes, and truly is well worth your time. How much does it cost to replace a 2015 Ford Escape? This problem is similar to other years of this generation of Escape. Average replacement costs for severe transmission issues on the 2015 Ford Escape (Model # 6F50 / 6F35) range anywhere from $2280.00 all the way up to $3387.00 but average out around $3150. The unfortunate nature of this repair is that it shows up rather suddenly. What was the biggest letdown...
Easy tips

How much does a Ford F 250 starter cost?

How much does a Ford F 250 starter cost? The best part is, our Ford F-250 Starter products start from as little as $41.99. When it comes to your Ford F-250, you want parts and products from only trusted brands. Why does my starter wear out on my Ford F-250? The starter on your F-250 Super Duty truck is key to going anywhere, it provides the initial momentum for the engine to turn over thus starting the motor. Over time it wears out from normal use, holding the key too long when starting it, and natural causes like corrosion. Where...
Common questions

Is there a recall on 2014 Ford Fusion transmission?

Is there a recall on 2014 Ford Fusion transmission? Summary: Ford Motor Company (Ford) is recalling certain 2013-2014 Ford Escape, and 2013-2016 Ford Fusion vehicles, equipped with six-speed automatic transmissions. The bushing that attaches the transmission shifter cable to the transmission may degrade over time and cause the bushing to detach from the transmission. What are the most common problems with a 2014 Ford Fusion? The most common issues you’ll encounter if you’re looking at used 2014 Ford Fusions are: Transmission failure. Cost to fix: Up to $3500 Suspension problems. Cost to fix: Varies, up to $1400 Here are all...
Easy tips

How long does it take to get your car to start?

How long does it take to get your car to start?  Touch the button to start your vehicle’s engine  Your request will typically take about to 3 minutes to process. If your vehicle has been parked for a while it can take up to 30 minutes for the request to reach your vehicle and perform the task. Requirements How long does it take to remote start a car? After 15 minutes if you have not entered your vehicle with the key, the engine will shut off automatically. This remote function requires your vehicle to be equipped with a...
Easy tips

How do I turn off MyKey limited volume?

How do I turn off MyKey limited volume? Go to the main menu, and select “Settings.” Scroll through your options, and select “MyKey.” Search for the option that says “Clear MyKey.” Select this setting, and press and hold “OK” until you see this message on your display screen: “All MyKeys Cleared.” How do I reset MyKey volume? To clear or change your MyKey settings, switch the ignition on using an admin key or fob....Clearing all MyKeysMessage. Action and Description.Settings. Press the OK button.MyKey. Press the OK button.Clear MyKey. Press and hold the OK button until the following message displays: “All...