Most popular

What causes the p0057 OBD-II trouble code?

What causes the p0057 OBD-II trouble code? When a P0057 trouble code sets it means that the powertrain control module has detected a fault, specifically low voltage, on the heater control circuit for the bank two sensor two oxygen sensor. What causes the P0057 code? How does the p0057 Toyota engine light work? P0057 TOYOTA Description Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal...
Easy lifehacks

When does a timing chain need to be replaced?

When does a timing chain need to be replaced? Every time you use the engine, the timing chain is in use. When does a timing chain need to be replaced? The timing chain normally needs to be replaced between 80,000 and 120,000 miles unless there is a specific problem. Issues with the chain are common in higher mileage vehicles. Can a loose timing chain cause an engine to backfire? Backfiring If your engine backfires, it could be due to a loose timing chain. If your vehicle loses power, without warning, your timing chain might be loose. If you notice your...
Common questions

What to do if your Chevy Cruze coil pack is bad?

What to do if your Chevy Cruze coil pack is bad? There are a lot of potential symptoms related to bad coil packs in your Cruze. We always recommend using an OBDII scanner to pull your trouble codes if the service engine soon light is on. It can really narrow your search down. If you don’t have one, your local parts store can do this for you at no charge. What's the problem with my 2013 Chevy Cruze? New member here. Not sure if this is the right place to post, so forgive me 2013 Cruze LT 1.4 with 114k...
Most popular

Why do low energy lights flash when turned off?

Why do low energy lights flash when turned off? The living room, low energy lamps had been rapidly flashing when switched off! just check the wiring, The neutral must connected to the lights first, then the hot line it must be connected into the switch then from switch going to lights. Just try or check it out. What are the symptoms of flashes of light? Other symptoms that may seem like flashes of light include: 1 Distorted vision (with migraine). 2 Halos around lights. 3 Starbursts around lights. When to see a doctor for flashing lights? You should see a...
Common questions

How often should you change the spark plugs on a 5.7 Hemi?

How often should you change the spark plugs on a 5.7 Hemi? The 2014 Rams with 5.7 Hemi motors are now getting an iridium spark plug with a factory change interval of 100,000 miles. How many spark plugs are in a 2005 Dodge Ram 5.7 Hemi? 16 spark plugs Now, let's review the procedures to replace the spark plugs on the 2004-2005 5.7L HEMI engine … eight of the 16 spark plugs are located under an ignition coil, those coils will have to be removed. Before removing or disconnecting any spark plug cables, note the original position of the cables....
Easy lifehacks

Where is the fuel pressure limiting valve pressure relief valve located on the Cummins engine?

Where is the fuel pressure limiting valve pressure relief valve located on the Cummins engine? On the ISX 15, the fuel pressure relief valve is on the end of the fuel rail toward the front of the engine. It is screwed directly into the fuel rail on one end and has a banjo type fuel line fitting on the other which is sealed by 2 sealing washers. What is the fuel pressure on a 5.9 Cummins? The rail pressure during normal idle should be 5,600 - 6,500 PSI (386 - 448 bar). 3. If checking a drivability issue the desired...
Common questions

How do rear axle bearings get lubricated?

How do rear axle bearings get lubricated? The seal is between the hub and the axle housing so keeps oil from leaking out behind the hub. There is plenty of room between the axle housing and the half shaft for oil to get through to the bearing. "The rear whel bearings recieve their lubrication from the rear axle. How do you keep bearings lubricated? Many different methods can be used to apply oils and greases, however, there are four standard methods that are typically used to supply lubrication to bearings.Oil drip feed lubrication.Oil splash feed lubrication.Oil force feed lubrication.Grease lubrication....
Most popular

What does Gen mean on a 97 Dodge Ram?

What does Gen mean on a 97 Dodge Ram? 1997 Dodge Ram 1500: the GEN light indicates that the charging system. 1997 Dodge Ram 1500. Is it possible to rebuild a Dodge transfer case? We offer the widest selection of rebuilt remanufactured transfer cases for Dodge vehicles including the following models: Colt Vista, D Series, Dakota, Durango, Ram 1500, Ram 2500, Ram 3500, Ramcharger and the W Series. Removing and replacing a transfer case with our remanufactured unit is much easier then overhauling the transfer case. Which is the best transfer case for Jeep 231? The NP231 transfer case has...
Other

How to install a side rear view mirror on a Dodge Ram truck?

How to install a side rear view mirror on a Dodge Ram truck? This video will show you how to install a replacement side rear-view mirror on a 2002-2008 Dodge Ram truck. For this auto repair, you will use a T40 Torx driver, a Phillips screwdriver, a flat blade screwdriver and a 10mm wrench. This video also contains instructions for the electrical hook-ups to control the mirror. What do I need to replace my side view mirror? Replacing your side view mirror glass requires just a few simple steps for most application. Ensure that you have the proper replacement mirror...
Other

Is the front axle of a Dodge Ram working?

Is the front axle of a Dodge Ram working? Discussion in ' Tech Info ' started by Brander, Nov 20, 2018 . Front axle will not engage, I can hear the Transfer Case switching when I turn the knob to 4wd but the front axle is not working. What to do if your 4 wheel drive won't engage? Since 2004+ they’ve been more robust and seldom cause issues. To test if the actuator is meshing and engaging, remove both lines and with the front still raised, the front CV shafts should be engaged and be rotating as well. Is the...