Easy tips

How do you remove the headliner from a car?

How do you remove the headliner from a car? Remove the old headliner. Pry off all the trim that surrounds the headliner and holds it in place. Detach and remove all of the seatbelt covers, lights, speakers, visors and clothes hangers. You may also have to remove some of the upper A, B, C pillar panels to get the headliner to drop form the roof area. Is it possible to install a new headliner? Fortunately, you can install a brand new headliner without too much trouble if you have the right materials. Start by removing all of the accessories that...
Easy lifehacks

How do you replace an air conditioner clutch in a Ford?

How do you replace an air conditioner clutch in a Ford? By following the procedures below, you can remove and replace the A/C compressor clutch in your Ford vehicle at minimal cost. Step 1 Have the air-conditioning system discharged or evacuated of refrigerant by certified personnel at a dealer service department or automotive air-conditioning repair facility. Is the arm of a hydraulic clutch replaceable? The arm provides the proper ratio for the great majority of pressure plates and the T6 hardened and hard anodized billet aluminum slave cylinder and piston are absolutely durable, yet rebuildable or replaceable down the road,...
Easy lifehacks

Where are the ball joints and tie rods located?

Where are the ball joints and tie rods located? Both ball joints and tie rod ends are each a part of the front suspension and steering system of your car and are located between the front wheels. The steering system spans the entire length between the front wheels, connecting the two wheels together, while the suspension system is contained just inside each front wheel. How do you replace a tie rod end ball joint? When the joint is riveted to the control arm, the rivets are drilled out or cut with an air chisel. The new joint is replaced using...
Most popular

How to find out if your car has a c0035 code?

How to find out if your car has a c0035 code? Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins. The cost to diagnose the C0035 code is 1.0 hour of labor. The auto repair's diagnosis time and labor rates vary by location, vehicle's make and model, and even your engine type. What causes a c0035 Chevrolet to go off the road? C0035 CHEVROLET Possible Causes 1 Faulty Left Front Wheel Speed Sensor 2 Left Front Wheel Speed Sensor harness is open or shorted 3 Left...
Easy lifehacks

What size speakers are in a 2001 Chevy Silverado 1500?

What size speakers are in a 2001 Chevy Silverado 1500? Speakers that fit your 2001 Chevrolet Silverado 1500*Speaker locationSpeaker sizes**Front Door6-3/4"Front Door TweetersTweeterFront Door Woofers6-3/4"Rear Door6-3/4" Is the Chevy Silverado 1500 an extended cab? Roomy extended cab models, strong V8 engines, available composite bed, disc brakes at all four corners, optional traction control. Cons: Cheap interior materials, sketchy build quality. What kind of car is a 2001 Chevy Silverado? Back in October 2001, my dad bought a Olympic White Extended Cab 5.3 LS 2001 Silverado and we have had it ever since. I received this car as my first car...
Most popular

What is the air pump on a DTC p0410?

What is the air pump on a DTC p0410? DTC P0410 Secondary Air Injection (AIR) System Refer to Engine Controls Schematics MAF, Secondary Air Injection Pump Bypass Solenoid, IAC and Secondary AIR Pump . Circuit Description The AIR pump is used on this vehicle to lower tail pipe emissions on start-up. What does the code p0410 mean on a car? Code P0410 is the result of the Engine Control Module (ECM) indicating a malfunctioning Secondary Air Injection System. This happens when the O2 sensor does not accurately detect the changes in the O2 level of the exhaust while the air...
Other

What are the problems with automatic locking hubs?

What are the problems with automatic locking hubs? The most common problem with automatic locking hubs is the hub won’t engage. Mud, rust or worn parts inside the hub can prevent the mechanism from sliding in and locking the hub. What happens when the hub is locked in 2WD mode? On some applications, only one side unlocks when in the 2WD mode. With this setup, the hub on the opposite side remains locked and the axle continues to turn with the wheel. But as long as the transfer case remains in the 2WD mode, the front wheels are not driven....
Easy tips

Are pink and red wires the same?

Are pink and red wires the same? “Pink” might be actually “red”, and is typically used for the wire carrying +5 volts. “Blue” might be “black” and is the usual color for Ground. If you really want to use that cable for something, it would be a really good idea to check which colors actually connect to which pins. Where is my vehicle speed sensor ( VSS ) wire located for? Where is my Vehicle Speed Sensor (VSS) Wire Located for Radio Installation? When you remove your OEM radio, there are 4 plugs that plug into the radio. Only 2...
Easy tips

What causes engine hesitation in an older car?

What causes engine hesitation in an older car? Older engine's are equipped with a distributor ignition system. This systems can cause hesitation when maladjusted, by using a timing light this situation can be checked and corrected. If the timing is adjusted too far retarded (behind the timing mark) in relationship to the engine crankshaft it will cause hesitation. Why does my car hesitate when I open the throttle? Many times an engine can hesitate without the computer detecting a problem, if this is the case proceed to the next step. Step 2 - Poor fuel pressure can cause the engine...
Other

Why does my Hilux make a knocking noise when cold start?

Why does my Hilux make a knocking noise when cold start? I have a 1KZTE which also will give slight valve noise in winter on cold start - goes away as soon as revs are off idle or within about 10-15 secs. This is normal as the engine needs to pump the oil up to the valves. What does it mean when your engine knocks on a cold start? Engine Knocking on cold Start. When an engine knock is most pronounced when releasing the throttle a “rod knock” as in Rod Knox, is indicated. And when the dipstick indicates that...