Common questions

Can you replace fuses with breakers?

Can you replace fuses with breakers? The primary reasons for replacing a fuse with a circuit breaker in a control panel are for convenience and operating cost. When a breaker trips, the “repair” is as simple as fl ipping a switch. But when a fuse is blown, the entire fuse needs to be replaced. Having a spare fuse on hand is recommended. Do modern circuit breakers have fuses? Unlike circuits, which can be used over and over again, fuses are one and done. And that's the whole story. Breaker boxes do not have fuses, because circuits are used instead. Do...
Other

How do you remove a transmission speed sensor?

How do you remove a transmission speed sensor? Remove the mounting bolts to the speed sensor. Unplug the harness from the sensor. Note: The mounting bolts that secure the drive shaft to the rear axle may have hex, allen, or torx heads. Step 5: Use a flat tip screwdriver and pop out the sensor. Keep in mind that about one quart of transmission fluid will leak out when you remove it. What happens when a transmission speed sensor goes out of alignment? If either of these two sensors falls out of alignment or experiences electrical issues, it impacts the operation...
Easy tips

Why did my cordless drill stop working?

Why did my cordless drill stop working? When a drill runs intermittently, the problem can be traced to a bad cord or worn brushes (sometimes the switch may be defective, but usually the switch fails in the "on" or the "off" position). The best way to check out a power cord is with a continuity tester or an ohm meter. Why has my drill stopped working? If your cordless drill won't turn on, it's not the end of its life. This is a common problem that can be fixed with help from our troubleshooting guide. Inspect these parts: the carbon...
Easy tips

How much torque does a Massey Ferguson tractor have?

How much torque does a Massey Ferguson tractor have? Where there is no published figures, then Massey Ferguson issue standard torque data. The first figure listed in the rows below (bold type) is the nominal size in inches. The second figure is the torque in lb-ft of non-rigid joints, limited strength nuts and standard nuts with lock washers (definitions given at end of this page). What kind of engine does a Ferguson 35 tractor have? Click here to see what we've got! Here are the data, specifications, dimensions, tolerances and the main tightening torque settings for the 3 cylinder Perkins...
Other

How do you repack a hydraulic cylinder?

How do you repack a hydraulic cylinder? Steps to Repack a Hydraulic CylinderRelease all pressure from the cylinder.Loosen and remove the hydraulic lines from the cylinder. Ensure the hydraulic cylinder is supported and won't drop. Remove the gland from the cylinder. Remove the piston rod from the cylinder. How do you test a hydraulic cylinder for bypass? The conventional way of testing the integrity of the piston seal in a double-acting cylinder is to pressurize the cylinder at the end of stroke and measure any leakage past the seal. This is commonly referred to as the "end-of-stroke bypass test". Which...
Easy lifehacks

Why is my loader not working on my Yanmar tractor?

Why is my loader not working on my Yanmar tractor? If the loader is NOT working then there is something wrong with the pump (normally caused by unhooking the hoses while the tractor is running which dead-heads the pump) or a problem with the oil supply (out of oil, dirty filter or screen?). You may need to remove the pump & inspect it for damage if the oil is full & the filters are clean. Where can I find information on Yanmar tractors? Helpful information and resources on Yanmar tractors from SSB Tractor, a leading provider of tractor parts, manuals,...
Other

Should I add brakes to my boat trailer?

Should I add brakes to my boat trailer? So does my boat trailer need brakes? It is recommended in the majority of the states that trailers with a total gross weight of over 3000 lb have to be equipped with an Independent braking system. However, most experts suggest that they should be installed on trailers 1500 lb or heavier. Do boat trailers use electric brakes? The trailer always brakes first, and this positive brake action is safer for downhill driving and quick stops. However, few boat trailers are equipped with electric brakes, but they're used on many RV and utility...
Easy tips

How to change timing on a Cummins injector?

How to change timing on a Cummins injector? Tighten the adjusting screw on the injector rocker lever until the timing plunger just touches bottom. Back out the adjusting screw on the injector rocker lever two flats (120 degrees). Two flats will provide 0.56 mm [0.022 in] lash. The specification is 0.50 to 0.74 mm [0.020 to 0.029 in] lash. Hold the adjusting screw and tighten the lock nut. What should the Lash be on a Cummins injector? Back out the adjusting screw on the injector rocker lever two flats (120 degrees). Two flats will provide 0.56 mm [0.022 in] lash....
Easy lifehacks

What kind of Turbo do I need for 6.7L Cummins?

What kind of Turbo do I need for 6.7L Cummins? Your first option is the upgraded VGT that will drop right in place of your stock turbo, but give you increased performance and longevity. BD Diesel & Fleece Performance both offer upgrades for the 6.7L Cummins. BD Diesel offers the Screamer Turbo and Fleece offers their signature Cheetah Turbo. How does a turbo work on a Cummins? As the steel ring rotates, the vanes move closer or further from the turbine wheel inside the housing creating more or less pressure between your engine and your turbo. This is controlled by...
Easy tips

How do you dial in a bellhousing Register?

How do you dial in a bellhousing Register? Again, making sure it is tight, but it is not necessary to torque the bolts. Place the base of the magnetic mount dial indicator on the friction contact area of the flywheel, then arrange the indicator arm so that it travels along the inside diameter of the bellhousing register hole. How to dial in a bellhousing-Silver Sport transmission? The first step is to assemble the flywheel to the crankshaft flange. Since we will only be using the flywheel to hold the magnetic-based dial indicator, you do not need to torque the bolts...