Other

Will a programmer hurt my truck?

Will a programmer hurt my truck? Can a Tuner Damage My Transmission? Tuners do not damage transmissions, drivers do. Drivers should practice caution and often times reprogram their truck to a lower HP tune depending on the conditions they will be driving in. For example, stock trucks should not be towing on a 120 HP tune. Are tuners bad for trucks? The short answer is that a tuner is not bad for your truck. Companies that manufacture such tuners have spent many years perfecting them to the point that your truck's engine remains in a healthy condition. This also boosts...
Common questions

What makes the warning lights on a Ford Focus stay on?

What makes the warning lights on a Ford Focus stay on? If it's the warning lites start with the ignition switch, if it's the dash lites themselves start with the light switch. Batteries are not made to be discharged then recharged on a regular basis. They actually make a battery for that it's called a deep cycle battery. How to package a Ford Focus dashboard instrument cluster? Package the Ford Focus dashboard instrument cluster inside a sturdy box with plenty of packaging material (make sure you include your confirmation email in the box). Send us your package by tracked courier...
Common questions

Why does my gears get stuck in drive?

Why does my gears get stuck in drive? You may have broke the shift cable and will need to have the cable checked to see if it broke and replace the cable. I have a vitz 2003 FL 1.3 automatic it jerks at slow speeds and low revs around 10 - 50 kmh . Also sometimes the gear gets stuck What to do if your transmission is stuck in drive? A failure of either part would allow you to move the shifter handle to park, while the transmission actually remains in drive. Because it could be either of these parts,...
Other

How much does a 1999 Ford F-250 Super Duty cost?

How much does a 1999 Ford F-250 Super Duty cost? Monthly Estimate based on a 4.4% rate for 60 months, $8,495 vehicle price, $0 down payment, $0 trade-in, $0 sales tax. Amazing! Small dealership with a very carefully selected inventory of reliable cars. Good atmosphere and very comfortable office space. The agent was very helpful and efficient. Prices are very reasonable. When was the last time I serviced my 1999 Ford F 250? Last serviced at 79,912 miles in Sioux Falls, SD on 05/12/21 • Vehicle serviced • Oil and filter changed. Mileage: 79,907 miles Body Type: Pickup Color: White...
Common questions

Is there a fuse for the trailer light?

Is there a fuse for the trailer light? Yes, depending on the year of the F150, they have fuses for the trailer harness. Brakes and left and right turn signals are all fused. I’ve diagnosed this problem twice on a friends 150 and it’s always been a fuse in the right, (passengers side,) kick panel. Check the owners manual, you’ll find it. Are there fuses for running and signal lights? There is 1 fuse for each side that does signal and braking. Running lights are on a separate fuse. But the truck lights work fine. Just the trailer has issues....
Common questions

What happens when a thrust bearing fails in an engine?

What happens when a thrust bearing fails in an engine? If an engine is assembled with too much end play in the crank, or if the thrust bearing fails, the forward movement of the crankshaft in the block can chew up the main bearing caps and block. Excessive end play can also cause connecting rods to fatigue and break, and wrist pins to work loose and score the cylinders. How are journal bearing and thrust bearing different? A journal bearing allows the shaft to rotate while holding it in a fixed horizontal position. On the other hand, a thrust bearing...
Other

Where is the gem module on a 1997 F150?

Where is the gem module on a 1997 F150? This 1997 Ford F150 needs the GEM module changed due to multiple conditions. To see testing that lead to this repair please click here. The GEM module is located at the rear of the interior fuse box. The first step is to remove the trim panel that covers the gap between the upper side of the steering column and the dash. How to change the gem module on a Sparkys F150? Four fasteners with 13 mm heads. Now wiggle, pry and twist the fuse box and GEM module assembly down. After...
Other

Is the new Ford Ranger selling well?

Is the new Ford Ranger selling well? Ford Ranger Sales - Q2 2020 - United States In the United States, Ford Ranger deliveries totaled 25,008 units in Q2 2020, an increase of about 20 percent compared to 20,880 units sold in Q2 2019. In the first six months of the year, Ranger sales increased about 52 percent to 45,988 units. Is the Ford Ranger Wildtrak worth £34, 000? The Ford Ranger Wildtrak certainly stands out from a crowd, but is it worth £34,000? Once the preserve of workmen and farmers, pickups like the Ford Ranger, Mitsubishi L200, Isuzu D-Max and...
Most popular

Do you have to reprogram a gem module?

Do you have to reprogram a gem module? no it DOES NOT need to be reprogrammed by ford the Vechicle Security Module needs to be reprogrammed if replaced. To further complicate matters, Ford says their GEM modules need to be programmed after they have been installed so they will function correctly. ... How does the gem control the starter motor? It also controls the starter motor. Mine will occasionally start itself if the key is in the on position and in park or neutral, even when running. Ouch! tinkering likes this. Eastmonsoon, I checked back through the wiring diagram for...
Most popular

Why is vxdiag Ford IDs manager initialization error?

Why is vxdiag Ford IDs manager initialization error? Give me error “Manager Initialization Error (Failed to initialize Vetronix Runtime rc=-5)” Any idea? 1.Don’t install IDS software with Benz C6 XENTRY software. IDS requires independent operating system. 2.Don’t use vci manager driver, the VCI Manager is for original vcm2 ids. Install VX Manager driver for vxdiag and start IDS on VXManager. How does the ordering process work at Ford? This system is to organize the order so they are "in a row" for scheduling. That way in the first pass of scheduling they only look at 1 truck per dealer, then...